I think you would benefit from this:
https://cnc4pc.com/c86-connector-acorn-cnc.html
https://cnc4pc.com/c34de-for-delta-b2-driver.html
Arturo Duncan
https:/cnc4pc.com
Search found 23 matches
- Fri Apr 19, 2024 4:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 28
- Views: 747
- Tue Apr 02, 2024 8:06 am
- Forum: Centroid Acorn CNC Controller
- Topic: Wiring multiple closed loop steppers
- Replies: 10
- Views: 1292
Re: Wiring multiple closed loop steppers
We have some connector boards that may help you wire this:
https://cnc4pc.com/c86-connector-acorn-cnc.html
https://cnc4pc.com/c34hs2-board.html
Arturo Duncan
https://cnc4pc.com
https://cnc4pc.com/c86-connector-acorn-cnc.html
https://cnc4pc.com/c34hs2-board.html
Arturo Duncan
https://cnc4pc.com
- Fri Mar 08, 2024 9:38 am
- Forum: Centroid Acorn CNC Controller
- Topic: CNC CONTROL SUGGESTIONS
- Replies: 28
- Views: 991
Re: CNC CONTROL SUGGESTIONS
We have some connector boards for those servos that I think should simplify your wiring:
https://cnc4pc.com/connector-board-for- ... -sgdm.html
https://cnc4pc.com/c86-connector-acorn-cnc.html
Arturo Duncan
https://cnc4pc.com
https://cnc4pc.com/connector-board-for- ... -sgdm.html
https://cnc4pc.com/c86-connector-acorn-cnc.html
Arturo Duncan
https://cnc4pc.com
- Thu Feb 08, 2024 8:47 am
- Forum: Centroid Acorn CNC Controller
- Topic: No Axis Motion with Acorn - Clearpath SDSK - C86ACCP
- Replies: 6
- Views: 537
Re: No Axis Motion with Acorn - Clearpath SDSK - C86ACCP
It should be something simple that you are overlooking. Since this systems acts as an interlocking system, one thing depends on the previous one, so going back again through the step by step instructions should reveal what the issue is: Some additional ideas on troubleshooting this are: - Temporaril...
- Mon Jun 13, 2022 10:07 am
- Forum: Centroid Acorn CNC Controller
- Topic: C86ACCP out of stock, should I skip it?
- Replies: 10
- Views: 2412
Re: C86ACCP out of stock, should I skip it?
I am sorry to all that were affected by the delay in having the C86ACCP. We had an item that became scarce. We have this solved and have plenty in stock and do not anticipate that will be having stock issues in the future.
Arturo Duncan
https://cnc4pc.com
Arturo Duncan
https://cnc4pc.com
- Wed Jan 05, 2022 11:23 am
- Forum: Centroid Acorn CNC Controller
- Topic: CNC4PC C86ACORN & C34 Connection to Closed Loop Stepper driver
- Replies: 25
- Views: 4461
Re: CNC4PC C86ACORN & C34 Connection to Closed Loop Stepper driver
Joe, Please try: - Disconnect the DRIVE _OK signal going into the ACORN and just set a jumper for now, so that CNC12 does not see the fault signal coming from the C86. - If the C86 continues to fault, confirm the driver itself is not faulting. You may need to check the encoder wiring or invert the A...
- Tue Mar 09, 2021 5:43 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New Centroid Teknic Clearpath officially supported configurations. Updated 5-10-23
- Replies: 54
- Views: 122871
Re: New Centroid Teknic Clearpath officially supported configurations
The DB25 will give you TTL output signals, which is great for most stepper systems. If using the terminals, you can pull-up to +5vdc. That is what we do with the C86ACCP and C86ACORN boards.
Arturo Duncan
https://cnc4pc.com
Arturo Duncan
https://cnc4pc.com
- Fri Oct 30, 2020 4:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Z-Axis with Brake problem (Resolved)
- Replies: 30
- Views: 11469
Re: Z-Axis with Brake problem (Resolved)
The C86 board does not invert the axes. But you can select the active high/low for any pin on the CNC12 software.
- Mon Oct 26, 2020 4:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Z-Axis with Brake problem (Resolved)
- Replies: 30
- Views: 11469
Re: Z-Axis with Brake problem
OK, you are using the axes enable. When you get the fault, is the green LED just before that? Can it be the system is trying to do motion before enabling the system? Do you get the green LED?
- Mon Oct 26, 2020 3:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Z-Axis with Brake problem (Resolved)
- Replies: 30
- Views: 11469
Re: Z-Axis with Brake problem
How are you activating the C86 board? Axis Enable? No_Fault?