Search found 23 matches

Go to advanced search

by arturod
Fri Apr 19, 2024 4:02 pm
Forum: Centroid Acorn CNC Controller
Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
Replies: 14
Views: 209

Re: Delta ASDA-B2 ACORN WIRING INFORMATION

I think you would benefit from this:
https://cnc4pc.com/c86-connector-acorn-cnc.html
https://cnc4pc.com/c34de-for-delta-b2-driver.html

Arturo Duncan
https:/cnc4pc.com
by arturod
Tue Apr 02, 2024 8:06 am
Forum: Centroid Acorn CNC Controller
Topic: Wiring multiple closed loop steppers
Replies: 10
Views: 359

Re: Wiring multiple closed loop steppers

We have some connector boards that may help you wire this:
https://cnc4pc.com/c86-connector-acorn-cnc.html
https://cnc4pc.com/c34hs2-board.html

Arturo Duncan
https://cnc4pc.com
by arturod
Fri Mar 08, 2024 9:38 am
Forum: Centroid Acorn CNC Controller
Topic: CNC CONTROL SUGGESTIONS
Replies: 28
Views: 901

Re: CNC CONTROL SUGGESTIONS

We have some connector boards for those servos that I think should simplify your wiring:
https://cnc4pc.com/connector-board-for- ... -sgdm.html
https://cnc4pc.com/c86-connector-acorn-cnc.html

Arturo Duncan
https://cnc4pc.com
by arturod
Thu Feb 08, 2024 8:47 am
Forum: Centroid Acorn CNC Controller
Topic: No Axis Motion with Acorn - Clearpath SDSK - C86ACCP
Replies: 6
Views: 504

Re: No Axis Motion with Acorn - Clearpath SDSK - C86ACCP

It should be something simple that you are overlooking. Since this systems acts as an interlocking system, one thing depends on the previous one, so going back again through the step by step instructions should reveal what the issue is: Some additional ideas on troubleshooting this are: - Temporaril...
by arturod
Mon Jun 13, 2022 10:07 am
Forum: Centroid Acorn CNC Controller
Topic: C86ACCP out of stock, should I skip it?
Replies: 10
Views: 2401

Re: C86ACCP out of stock, should I skip it?

I am sorry to all that were affected by the delay in having the C86ACCP. We had an item that became scarce. We have this solved and have plenty in stock and do not anticipate that will be having stock issues in the future.

Arturo Duncan
https://cnc4pc.com
by arturod
Wed Jan 05, 2022 11:23 am
Forum: Centroid Acorn CNC Controller
Topic: CNC4PC C86ACORN & C34 Connection to Closed Loop Stepper driver
Replies: 25
Views: 4392

Re: CNC4PC C86ACORN & C34 Connection to Closed Loop Stepper driver

Joe, Please try: - Disconnect the DRIVE _OK signal going into the ACORN and just set a jumper for now, so that CNC12 does not see the fault signal coming from the C86. - If the C86 continues to fault, confirm the driver itself is not faulting. You may need to check the encoder wiring or invert the A...
by arturod
Tue Mar 09, 2021 5:43 pm
Forum: Centroid Acorn CNC Controller
Topic: New Centroid Teknic Clearpath officially supported configurations. Updated 5-10-23
Replies: 53
Views: 119818

Re: New Centroid Teknic Clearpath officially supported configurations

The DB25 will give you TTL output signals, which is great for most stepper systems. If using the terminals, you can pull-up to +5vdc. That is what we do with the C86ACCP and C86ACORN boards.

Arturo Duncan
https://cnc4pc.com
by arturod
Fri Oct 30, 2020 4:02 pm
Forum: Centroid Acorn CNC Controller
Topic: Z-Axis with Brake problem (Resolved)
Replies: 30
Views: 11443

Re: Z-Axis with Brake problem (Resolved)

The C86 board does not invert the axes. But you can select the active high/low for any pin on the CNC12 software.
by arturod
Mon Oct 26, 2020 4:54 pm
Forum: Centroid Acorn CNC Controller
Topic: Z-Axis with Brake problem (Resolved)
Replies: 30
Views: 11443

Re: Z-Axis with Brake problem

OK, you are using the axes enable. When you get the fault, is the green LED just before that? Can it be the system is trying to do motion before enabling the system? Do you get the green LED?
by arturod
Mon Oct 26, 2020 3:28 pm
Forum: Centroid Acorn CNC Controller
Topic: Z-Axis with Brake problem (Resolved)
Replies: 30
Views: 11443

Re: Z-Axis with Brake problem

How are you activating the C86 board? Axis Enable? No_Fault?

Go to advanced search