Search found 20 matches
- Sat May 16, 2020 12:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: How to let an M command trigger an output
- Replies: 7
- Views: 2975
Re: How to let an M command trigger an output
Hi Marty.. My problem with the predefined functions was that M8/M9 already was used by the "flood" function. Router dust collection uses the same M8/M9. So now I configured it as followed. As soon as I run a file my spindlecooler goes on imediately. After that the router goes to the toolch...
- Sat May 16, 2020 8:05 am
- Forum: Centroid Acorn CNC Controller
- Topic: How to let an M command trigger an output
- Replies: 7
- Views: 2975
Re: How to let an M command trigger an output (solved) Check PLC output.. not correct
Check If you run into the same issue as I did.
The output LED is wrong in the manual... should be 1122 for this event number
The output LED is wrong in the manual... should be 1122 for this event number
- Sat May 16, 2020 8:00 am
- Forum: Centroid Acorn CNC Controller
- Topic: How to let an M command trigger an output
- Replies: 7
- Views: 2975
Re: How to let an M command trigger an output
Thanks Swissi..
Al I needed to know
Al I needed to know
- Sat May 16, 2020 7:59 am
- Forum: Centroid Acorn CNC Controller
- Topic: How to let an M command trigger an output
- Replies: 7
- Views: 2975
Re: How to let an M command trigger an output
I thought I'd explained well Marty... Just a couple of buttons to trigger an output.. And an M number to trigger them in my custom G-code so my dust collector and my workshop ventilation kicks in whenever I start a Job.. Here is my BIG comment...."We can't SEE what you SEE" Please follow t...
- Fri May 15, 2020 12:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: How to let an M command trigger an output
- Replies: 7
- Views: 2975
How to let an M command trigger an output
Ok here my big question… I’m setting up my outputs on the standard acorn output relay board 1-8 1 output is hard wired to my spindle cooler… but it is named “Flood” because that is controlling output 1 2 output is spare 3 output is hard wired to my dustcollector wich should start whenever I start ro...
- Mon Apr 27, 2020 3:27 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Gantry Squaring
- Replies: 5
- Views: 3137
Re: Gantry Squaring
No it is possible I think to use NO switches BUT.. alle switches concerning safety should be NC switches if possible.. In industrial inviroment is is a must as wel...(at least in The Netherlands) This way there is also a cable "check" is it fails.. It is not expensive and most limit switch...
- Sat Nov 23, 2019 5:15 am
- Forum: Success Stories
- Topic: Workbee/Openbuilds conversion 1000x1500 CNC
- Replies: 4
- Views: 5452
Update Workbee/Openbuilds conversion 1000x1500 CNC
Hi, Here's a little update converting my Workbee CNC to a decent CNC router. So far I've added a new gantry and Z axis. Because of the light bending of the previous gantry I took a 160mm heavy duty extruded profile. I knew my new spindle would be a lot havier as well so good choice there. The spindl...
- Sun Oct 27, 2019 1:36 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Jog panel question (SOLVED)
- Replies: 8
- Views: 3127
Re: Acorn Jog panel question
Indeed solved..
Good to know for other people outside US
Regards
Vincent
Good to know for other people outside US
Regards
Vincent
- Fri Oct 25, 2019 12:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Jog panel question (SOLVED)
- Replies: 8
- Views: 3127
Re: Acorn Jog panel question
Thanks Marty
I'm going to play with the window settings
Report is attached
I'm going to play with the window settings
Report is attached
- Fri Oct 25, 2019 11:26 am
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Jog panel question (SOLVED)
- Replies: 8
- Views: 3127
Re: Acorn Jog panel question
Marty
I just use the normal windows keyboard. Don't have any other. And no If I hit the page up/down it goes back into incremental mode..
Can it have to do something with US/Dutch keyboard as setup in windows?
I just use the normal windows keyboard. Don't have any other. And no If I hit the page up/down it goes back into incremental mode..
Can it have to do something with US/Dutch keyboard as setup in windows?