Search found 20 matches

by RaptorMachine
Tue Feb 07, 2023 4:58 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Lube Pump Alarm 405 on M400s
Replies: 5
Views: 34

Re: Lube Pump Alarm 405 on M400s

additionally i have tried jumping the float switch AND have also tried leaving it open no luck
by RaptorMachine
Tue Feb 07, 2023 4:49 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Lube Pump Alarm 405 on M400s
Replies: 5
Views: 34

Re: Lube Pump Alarm 405 on M400s

thanks for the help attached you will find the file required. parameter 178 is 0.00 additionally after some thought i see that the machine MAY have had a controlled spindle.. at this time i do not. i see some notes on the schematic that may have relevance " input 3 must be jumpered to TB1 / 15B...
by RaptorMachine
Mon Feb 06, 2023 5:57 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Lube Pump Alarm 405 on M400s
Replies: 5
Views: 34

Lube Pump Alarm 405 on M400s

Hi Guys, need help with Centroid M4oos System ID # 0316041244 CNC 7 v 8.22 this is a system transplant i purchased used and i am attaching it to a Bridgeport mill report.zip i have the system booted and it loads completely. i am getting a fault 405 " lubricant level low " i checked the sch...
by RaptorMachine
Mon Jan 23, 2023 10:20 pm
Forum: Buy, Sell, Trade
Topic: CNC 4 System
Replies: 0
Views: 188

CNC 4 System

Pulling a CNC 4 system off a Bridgeport mill have the system booted up to dos ( dont have the system discs ) screen is bright and clear with no noticeable burn. tactile keyboard is in excellent shape i believe the servos are shot. any interest in parts or whole ? maybe can keep an old system alive.....
by RaptorMachine
Wed Feb 10, 2021 8:40 pm
Forum: Centroid Acorn CNC Controller
Topic: Acorn DMM Power requrement sanity check
Replies: 6
Views: 1870

Re: Acorn DMM Power requrement sanity check

I would say the servo breakers are properly sized to prevent damage to the motors and drives, but you will NEVER see a combined load of 60 amps from them. A 30A main disconnect (or 45A) with a 30A main breaker should be more than enough for that system. thanks for the reply Tom, so a 30 amp main to...
by RaptorMachine
Wed Feb 10, 2021 8:14 pm
Forum: Centroid Acorn CNC Controller
Topic: Acorn DMM Power requrement sanity check
Replies: 6
Views: 1870

Re: Acorn DMM Power requrement sanity check

looking a little closer at the DMM videos, do i need a contactor per DYN4 ? and they are showing a 20 amp circuit breaker followed by a 12 amp contactor.. so power ----- circuit breaker ------ contactor -------- DYN4

thanks in advanced

Joe
by RaptorMachine
Wed Feb 10, 2021 6:05 pm
Forum: Centroid Acorn CNC Controller
Topic: Acorn DMM Power requrement sanity check
Replies: 6
Views: 1870

Re: Acorn DMM Power requrement sanity check

one last thing.. maybe someone can recommend a nice terminal block for the main power.. thanks !
by RaptorMachine
Wed Feb 10, 2021 5:04 pm
Forum: Centroid Acorn CNC Controller
Topic: Acorn DMM Power requrement sanity check
Replies: 6
Views: 1870

Acorn DMM Power requrement sanity check

Hey guys, i want to be safe but not overkill. currently ordering breakers e stop contactor etc and just want to make sure i order the correct parts.. system background Bridgeport BOSS 2 hp spindle motor using a FMX TD 400 3 HP VFD with a 10.5A output ( will be running 220 single phase input ) 3 DMM ...
by RaptorMachine
Wed Dec 16, 2020 6:08 pm
Forum: Centroid Acorn CNC Controller
Topic: VFD recommendation needed ! Bridgeport Boss Acorn conversion
Replies: 6
Views: 2266

Re: VFD recommendation needed ! Bridgeport Boss Acorn conversion

Did some work on the machine today.. replaced all the bijur metering blocks, cleaned out all the lines, replaced a few, cleaned the automatic oiler, replaced the filter, had the electronics cabinet blasted and powder coated.. pretty good match... re-installed it, test fit the backplane, now its back...
by RaptorMachine
Wed Dec 16, 2020 12:56 pm
Forum: Centroid Acorn CNC Controller
Topic: VFD recommendation needed ! Bridgeport Boss Acorn conversion
Replies: 6
Views: 2266

Re: VFD recommendation needed ! Bridgeport Boss Acorn conversion

Hey Guys, thanks for all the help and info !!! greatly appreciate it !!! getting super excited to getting this machine running..

this is the vfd i ended up purchasing ..

https://www.factorymation.com/TD400-2003-13PH

with the braking transistor...

Joe