Search found 40 matches
- Tue Feb 07, 2023 4:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Lube Pump Alarm 405 on M400s
- Replies: 18
- Views: 3123
Re: Lube Pump Alarm 405 on M400s
additionally i have tried jumping the float switch AND have also tried leaving it open no luck
This post has been liked 0 time(s).
- Tue Feb 07, 2023 4:49 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Lube Pump Alarm 405 on M400s
- Replies: 18
- Views: 3123
Re: Lube Pump Alarm 405 on M400s
thanks for the help attached you will find the file required. parameter 178 is 0.00 additionally after some thought i see that the machine MAY have had a controlled spindle.. at this time i do not. i see some notes on the schematic that may have relevance " input 3 must be jumpered to TB1 / 15B...
This post has been liked 0 time(s).
- Mon Feb 06, 2023 5:57 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Lube Pump Alarm 405 on M400s
- Replies: 18
- Views: 3123
Lube Pump Alarm 405 on M400s
Hi Guys, need help with Centroid M4oos System ID # 0316041244 CNC 7 v 8.22 this is a system transplant i purchased used and i am attaching it to a Bridgeport mill report.zip i have the system booted and it loads completely. i am getting a fault 405 " lubricant level low " i checked the sch...
This post has been liked 0 time(s).
- Mon Jan 23, 2023 10:20 pm
- Forum: Buy, Sell, Trade
- Topic: CNC 4 System
- Replies: 1
- Views: 6887
CNC 4 System
Pulling a CNC 4 system off a Bridgeport mill have the system booted up to dos ( dont have the system discs ) screen is bright and clear with no noticeable burn. tactile keyboard is in excellent shape i believe the servos are shot. any interest in parts or whole ? maybe can keep an old system alive.....
This post has been liked 0 time(s).
- Wed Feb 10, 2021 8:40 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn DMM Power requrement sanity check
- Replies: 6
- Views: 2835
Re: Acorn DMM Power requrement sanity check
I would say the servo breakers are properly sized to prevent damage to the motors and drives, but you will NEVER see a combined load of 60 amps from them. A 30A main disconnect (or 45A) with a 30A main breaker should be more than enough for that system. thanks for the reply Tom, so a 30 amp main to...
This post has been liked 0 time(s).
- Wed Feb 10, 2021 8:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn DMM Power requrement sanity check
- Replies: 6
- Views: 2835
Re: Acorn DMM Power requrement sanity check
looking a little closer at the DMM videos, do i need a contactor per DYN4 ? and they are showing a 20 amp circuit breaker followed by a 12 amp contactor.. so power ----- circuit breaker ------ contactor -------- DYN4
thanks in advanced
Joe
thanks in advanced
Joe
This post has been liked 0 time(s).
- Wed Feb 10, 2021 6:05 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn DMM Power requrement sanity check
- Replies: 6
- Views: 2835
Re: Acorn DMM Power requrement sanity check
one last thing.. maybe someone can recommend a nice terminal block for the main power.. thanks !
This post has been liked 0 time(s).
- Wed Feb 10, 2021 5:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn DMM Power requrement sanity check
- Replies: 6
- Views: 2835
Acorn DMM Power requrement sanity check
Hey guys, i want to be safe but not overkill. currently ordering breakers e stop contactor etc and just want to make sure i order the correct parts.. system background Bridgeport BOSS 2 hp spindle motor using a FMX TD 400 3 HP VFD with a 10.5A output ( will be running 220 single phase input ) 3 DMM ...
This post has been liked 0 time(s).
- Wed Dec 16, 2020 6:08 pm
- Forum: Centroid Acorn CNC Controller
- Topic: VFD recommendation needed ! Bridgeport Boss Acorn conversion
- Replies: 6
- Views: 3195
Re: VFD recommendation needed ! Bridgeport Boss Acorn conversion
Did some work on the machine today.. replaced all the bijur metering blocks, cleaned out all the lines, replaced a few, cleaned the automatic oiler, replaced the filter, had the electronics cabinet blasted and powder coated.. pretty good match... re-installed it, test fit the backplane, now its back...
This post has been liked 0 time(s).
- Wed Dec 16, 2020 12:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: VFD recommendation needed ! Bridgeport Boss Acorn conversion
- Replies: 6
- Views: 3195
Re: VFD recommendation needed ! Bridgeport Boss Acorn conversion
Hey Guys, thanks for all the help and info !!! greatly appreciate it !!! getting super excited to getting this machine running..
this is the vfd i ended up purchasing ..
https://www.factorymation.com/TD400-2003-13PH
with the braking transistor...
Joe
this is the vfd i ended up purchasing ..
https://www.factorymation.com/TD400-2003-13PH
with the braking transistor...
Joe
This post has been liked 0 time(s).