Search found 90 matches
- Sat Apr 13, 2024 1:31 pm
- Forum: Acorn CNC Plasma
- Topic: Post Processor Sheet Cam/Fusion 360
- Replies: 10
- Views: 8243
Re: Post Processor Sheet Cam/Fusion 360
Did you get this worked out? I am using the Fusion 360 post and may be able to help.
This post has been liked 0 time(s).
- Sat Mar 02, 2024 11:25 am
- Forum: Acorn CNC Plasma
- Topic: Post Processor Sheet Cam/Fusion 360
- Replies: 10
- Views: 8243
Re: Post Processor Sheet Cam/Fusion 360
Joey, I use the Fusion PP which is very basic. I want to mark (center punch) small holes which the Fusion post doesn't do. Does the Sheet Cam post have support for marking and possibly feed reduction for small holes? Other features not in the Fusion post? I use the Fusion post because I use Fusion 3...
This post has been liked 0 time(s).
- Fri Mar 01, 2024 3:29 pm
- Forum: Acorn CNC Plasma
- Topic: Material Profiles
- Replies: 10
- Views: 1761
Re: Material Profiles
I plan to purchase the THC when I get the mechanics of the machine dialed in. The X-axis upgrade really helped but I would like to replace the bearing carriages on the Y-Axis with linear rails. My NEMA 23 motors with the 5:1 gearboxes seem to be working well. But maybe I need larger pinion gears. I ...
This post has been liked 0 time(s).
- Fri Mar 01, 2024 2:43 pm
- Forum: Acorn CNC Plasma
- Topic: Material Profiles
- Replies: 10
- Views: 1761
Re: Material Profiles
I ran the new set of test today. I think all the cuts were much better in the curves. There is still more dross than I think there should be on most of them. They are all with 3200 steps/rev and .2 Accel/Decel and smoothing on. I also set pierce delay to zero. It looks like the pierce is ready to go...
This post has been liked 0 time(s).
- Thu Feb 29, 2024 6:47 pm
- Forum: Acorn CNC Plasma
- Topic: Material Profiles
- Replies: 10
- Views: 1761
Re: Material Profiles
I upped the steps / rev to 3600 and the accel/Decell to 0.2 and did dry runs up to 230 IPM with smoothing on. Motion looked really smooth going into the curves. Then it started raining so I had to move the table back into the garage before doing any cuts. Hopefully, I can run the full set of test to...
This post has been liked 0 time(s).
- Wed Feb 28, 2024 4:01 pm
- Forum: Acorn CNC Plasma
- Topic: Material Profiles
- Replies: 10
- Views: 1761
Re: Material Profiles
Here is a link to the cut test I ran yesterday. I started with the default Powermax 45XP 10ga mild steel profile (without smoothing) at 129 IPM. I did 6 test cuts increasing the feed rate by 20 IPM for each test (129, 150, 170, 190, 210, and 230). Then I repeated the 6 test decreasing the feed rate ...
This post has been liked 0 time(s).
- Wed Feb 28, 2024 2:41 pm
- Forum: Acorn CNC Plasma
- Topic: Material Profiles
- Replies: 10
- Views: 1761
Re: Material Profiles
Thanks Joey. I will upload a new report after I get out to the shop today. I got the Accel/Decell rate down to .3 now but have not tried lower yet.
This post has been liked 0 time(s).
- Wed Feb 28, 2024 2:12 pm
- Forum: Acorn CNC Plasma
- Topic: Material Profiles
- Replies: 10
- Views: 1761
Material Profiles
I understand that Material Profiles is one of the many features of the Acorn Plasma controller. I use the Fusion 360 post from Centroid and can see that all of the feed values have been removed. When cutting with a Hypertherm 45XP 10ga mild steel profile I see that straight line cuts go at the profi...
This post has been liked 0 time(s).
- Tue Feb 13, 2024 9:20 pm
- Forum: Acorn CNC Plasma
- Topic: DIY Table Upgrades
- Replies: 19
- Views: 5684
- Tue Feb 13, 2024 6:56 pm
- Forum: Acorn CNC Plasma
- Topic: DIY Table Upgrades
- Replies: 19
- Views: 5684
Re: DIY Table Upgrades
Joey, You mentioned in a previous post that my resolution was really low. My drive will do 1/16 micro stepping but I haven't tried it yet. By my calculation my resolution should be 0.0004" per step. Am I calculation it correctly? McMaster 6325K13 pinion gear(PD=1.00) Gearbox 5:1 (inches / rev) ...
This post has been liked 0 time(s).