Search found 21 matches
- Mon Feb 08, 2021 2:02 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Reusing Anilam snubbers & capacitor?
- Replies: 16
- Views: 5482
Re: Reusing Anilam snubbers & capacitor?
They work great in new system. I chose to use all three caps and its working well.
- Tue Jan 12, 2021 1:47 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Anilam to Allin1 conversion
- Replies: 20
- Views: 8341
Re: Anilam to Allin1 conversion
I converted my Aniliam: reused transformer, caps, diodes. Put all in one’s seperate powersupply and caps below allinone board Added 24v transformer and bridge rectifier for it. Absolutly purchase the recommended VFD: forget the Chinese crap! Added braking resistor. Hardest part of job for me was add...
- Mon Oct 21, 2019 7:20 pm
- Forum: Success Stories
- Topic: 42” manual Kondia’s evolution to allinonedc
- Replies: 3
- Views: 4361
Re: 42” manual Kondia’s evolution to Allinonedc
Machine is up and running! The assembly manual is fantastic! I had only a couple minor issues that were expertly answered on the support forum.
- Mon Oct 21, 2019 7:15 pm
- Forum: Success Stories
- Topic: 42” manual Kondia’s evolution to allinonedc
- Replies: 3
- Views: 4361
Re: 42” manual Kondia’s evolution
Machine worked but the electrics eventually failed... Centroid to the rescue! I have used original servos, power box, transformer and caps along with some cabling. Room runs out quickly in this cabinet! Boring the servos for a 6mm shaft for the new encoders was the most difficult setup. Managed to m...
- Mon Oct 21, 2019 7:01 pm
- Forum: Success Stories
- Topic: 42” manual Kondia’s evolution to allinonedc
- Replies: 3
- Views: 4361
42” manual Kondia’s evolution to allinonedc
Bought this used Kondia mill about twenty years ago to help keep things working on the ranch. I eventually wanted to upgrade it but retain manual use characteristics. I bought some old Anilam parts stripped off an old Bridgeport and began adapting things to my mill- except my machine is generally me...
- Sun Oct 13, 2019 9:45 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Autotune
- Replies: 2
- Views: 1578
Re: Autotune
Thanks! will read up... That is easy! just a note: the support here is fantastic! Not used to it as i am coming from the IT world where finger pointing to the other guy is the usual answer. lol. Thanks again!
- Sun Oct 13, 2019 9:11 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Autotune
- Replies: 2
- Views: 1578
Autotune
My mill is limited to 3.60 in Z- not enough for autotune. Is it possible to edit the file to tune Z in a shorter area or must I go manual tune? Allinonedc system.
- Sat Oct 12, 2019 12:43 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: no Motion after tripping limit switches <resolved>
- Replies: 6
- Views: 2640
Re: no Motion after tripping limit switches
THANK YOU! THANK YOU! martyscncgarage - I had software flipped switches but had not moved wires- THAT IS THE SOLUTION! Might be nice to add to manual. Your a genius!
- Fri Oct 11, 2019 11:49 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: no Motion after tripping limit switches <resolved>
- Replies: 6
- Views: 2640
Re: no Motion after tripping limit switches
you are correct. i spent some time and did some reconfiguring before i got your information so i should post an updated report. System sets fine if i use ‘ jog’ and place everything centered- even the soft stops trigger properly and i can back off.
- Thu Oct 10, 2019 4:03 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: no Motion after tripping limit switches <resolved>
- Replies: 6
- Views: 2640
Re: no Motion after tripping limit switches
report attached.