Search found 2243 matches
- Wed May 01, 2024 8:55 am
- Forum: Centroid Acorn CNC Controller
- Topic: AcornSix issues
- Replies: 8
- Views: 130
Re: AcornSix issues
At what point going backwards do the Acorn Six boards need a firmware update for this? Can you share a date or serial number where the boards need a firmware update? Thanks.
- Tue Apr 30, 2024 8:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Tool touch off and probe help needed
- Replies: 23
- Views: 280
Re: Tool touch off and probe help needed
OK, seeing what drives you have it's impossible to have the steps per rev you have set in the wizard. Set the drives and wizard to be 1600 or 3200. The values you have are incorrect. Did you come over from a Mach3 setup? Read this topic as anything else you do right now is a moot point, you have to ...
- Tue Apr 30, 2024 4:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Tool touch off and probe help needed
- Replies: 23
- Views: 280
Re: Tool touch off and probe help needed
A side note here, looking at your report, I'm not sure how you came up with your steps per revolution. You have them set to 25,400 on the X and Y and 40,650 on the Z axis. Can you share how you got those numbers as those are incorrect settings for Acorn and your drives. What drives are you using? An...
- Mon Apr 29, 2024 10:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Tool touch off and probe help needed
- Replies: 23
- Views: 280
Re: Tool touch off and probe help needed
Please tell us what is happening and why it's not working? What macro are you using? Please post a current report from the machine and/or the PDF with all your current wizard settings. We can't really help unless we know how you are setup and what is or isn't happening. Open the wizard press CTRL P ...
- Fri Apr 26, 2024 4:24 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CL57T (3.0) Stepper Diver Issue (DB25 - Step Pull Up/Down Voltage Issue?) <resolved>
- Replies: 7
- Views: 331
- Fri Apr 26, 2024 10:06 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: OPCON and USB-BOB
- Replies: 82
- Views: 8198
Re: OPCON and USB-BOB
There are lots of joysticks for two axis moving, like in any RC control, or here is an example of a profile measuring machine in my job. But these are analogue, more throw, more speed, or in RC controls more travel speed depending on what is controlled. Uwe Uwe, I already asked about analog joystic...
- Thu Apr 25, 2024 9:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Enable outputs on Acorn
- Replies: 9
- Views: 278
Re: Enable outputs on Acorn
Yes, what he's talking about doing makes no sense at all. Hopefully he'll elaborate on the "why".
- Thu Apr 25, 2024 9:11 am
- Forum: Centroid Acorn CNC Controller
- Topic: Enable outputs on Acorn
- Replies: 9
- Views: 278
Re: Enable outputs on Acorn
I am using a DB25 interface for my stepper motor outputs. While using this are the enable outputs on H2 and H3 still active to use? If so are the active high or low for enabled? Please tell us what stepper drive you are using, most stepper drives are enabled by default and the ENA connection is not...
- Wed Apr 24, 2024 7:07 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Losing connection with open loop steppers.
- Replies: 6
- Views: 229
Re: Losing connection with open loop steppers.
Please post a CURRENT report from the machine. Anytime you have issues AND you have made machine changes you must post a new report so we can see your current settings. We can see how the machine is setup and look at your error log as to what the issue might be.
- Wed Apr 24, 2024 3:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Ping Test Failed (10.168.41.2)
- Replies: 13
- Views: 306
Re: Ping Test Failed (10.168.41.2)
Sorry ShawnM, I guess my original post wasn't completely clear. It did get to the point were I was unable to reconnect. I have gone back through and used the PC tuner, and worked through Tech Bulletin 270. I downloaded all windows updates and verified that the firewall is still off. I am getting th...