Resolved..... For some reason the Ethernet thought it was connecting to CNC12 Mill. So I changed Ethernet setting to a totally different one. Rebooted. Then restarted and then changed to the correct Ethernet. When I tried to load Lathe Acorn it reinstalled the lathe software.
Whew......
Search found 19 matches
- Sat May 23, 2020 4:29 pm
- Forum: Centroid Acorn CNC Controller
- Topic: On Startup, CNC12 Mill overwrote Lathe Software (Resolved)
- Replies: 2
- Views: 1307
- Sat May 23, 2020 3:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: On Startup, CNC12 Mill overwrote Lathe Software (Resolved)
- Replies: 2
- Views: 1307
On Startup, CNC12 Mill overwrote Lathe Software (Resolved)
I am using the same computer for both Acorn boards for a couple months. I physically move the computer from one machine to the other and the Ethernet connections are never connected at the same time. So this morning I moved the computer to the lathe and turned it on. The CNC12 mill automatically sta...
- Thu May 14, 2020 3:33 pm
- Forum: Success Stories
- Topic: Recent upgrade to Acorn
- Replies: 2
- Views: 3287
- Thu May 14, 2020 3:26 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNCDrive DG4S Wiring / Configuration
- Replies: 16
- Views: 6268
Re: CNCDrive DG4S Wiring / Configuration
I will post a pictures here in a few. LoL, I'm sure you will get a laugh of how the machine has evolved over the years...... I don't want to talk bad about Mach because it served me for a good ten years but now that Acorn is up and running I cannot believe the difference. During this time down time ...
- Wed May 13, 2020 11:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNCDrive DG4S Wiring / Configuration
- Replies: 16
- Views: 6268
Re: CNCDrive DG4S Wiring / Configuration
Here is the picture. It came when I originally bought the DG4S drivers 3 to 4 years ago.
- Wed May 13, 2020 11:13 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNCDrive DG4S Wiring / Configuration
- Replies: 16
- Views: 6268
Re: CNCDrive DG4S Wiring / Configuration
Problem found...... First I want to think everyone for posting and helping👍. Marty, next time I think I have a better understanding how to communicate or at least show the things you need to see to help in the future. (Hope not not needed but probably will 😁) The 3C4DG interface card make for the DG...
- Tue May 12, 2020 12:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNCDrive DG4S Wiring / Configuration
- Replies: 16
- Views: 6268
Re: CNCDrive DG4S Wiring / Configuration
Thank you Marty. It took this for me to really understand your "See what you see" means, even when I read that post before I started this blog.
I will do a better job with the up coming replies. Great job on videos btw.
I will do a better job with the up coming replies. Great job on videos btw.
- Mon May 11, 2020 8:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNCDrive DG4S Wiring / Configuration
- Replies: 16
- Views: 6268
Re: CNCDrive DG4S Wiring / Configuration
Tried both, doesn't matter. I haven't been this frustrated in years. I have checked everything over and over... really only three control wires between the drive and Acorn. There is no way all 4 drives went out when all worked before pulling the other controller card. Using a bolt voltmeter set on m...
- Mon May 11, 2020 6:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNCDrive DG4S Wiring / Configuration
- Replies: 16
- Views: 6268
Re: CNCDrive DG4S Wiring / Configuration
Just curious, are you powering the control side of your DG4S with 12volts or 5 volts?
- Mon May 11, 2020 1:01 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNCDrive DG4S Wiring / Configuration
- Replies: 16
- Views: 6268
Re: CNCDrive DG4S Wiring / Configuration
Thank you for the reply. The DG4S drives are in correct state as you listed above in your comment number 1. No red light, green blinking, motors holding in place without any connections to Acorn. As you mentioned, no connection on pin 5 or 6 either. Yes I used the USB interface and got them configur...