Search found 30 matches
- Fri May 14, 2021 9:42 am
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn conversion
- Replies: 10
- Views: 3540
Re: Acorn conversion
Acorn was designed to work with a touchscreen PC so YES it will work no problem. Your post mentions upgrading the MX2 - going to centroid controls will be basically be a whole new control system - the old MX2 will be thrown in the dumpster. You will be far better off with the Centroid "All-in-1...
- Fri May 14, 2021 9:24 am
- Forum: Centroid Acorn CNC Controller
- Topic: proLIGHT 2000 Conversion to Acorn
- Replies: 43
- Views: 14919
Re: proLIGHT 2000 Conversion to Acorn
Thanks Tom and Marty, your above posts have given me the info that I was not fully understanding.
Looks like I need to tune my spindle controller which I have not attempted at all. Now it makes sense.
Looks like I need to tune my spindle controller which I have not attempted at all. Now it makes sense.
- Mon Apr 26, 2021 3:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: proLIGHT 2000 Conversion to Acorn
- Replies: 43
- Views: 14919
Re: proLIGHT 2000 Conversion to Acorn
Here is the manual for the BOSS spindle controller.
- Mon Apr 26, 2021 3:40 pm
- Forum: Centroid Acorn CNC Controller
- Topic: proLIGHT 2000 Conversion to Acorn
- Replies: 43
- Views: 14919
Re: proLIGHT 2000 Conversion to Acorn
Hi Marty,
Yes I can currently raise and lower the speed via the VCP but the numbers shown on the screen are WAY off from what the actual machine rpm is.
Let me dig up the manual.
Should I be putting in the min/max speeds for the electric motor (aka 7200 rpm max) or for the machine (10k) ?
Yes I can currently raise and lower the speed via the VCP but the numbers shown on the screen are WAY off from what the actual machine rpm is.
Let me dig up the manual.
Should I be putting in the min/max speeds for the electric motor (aka 7200 rpm max) or for the machine (10k) ?
- Mon Apr 26, 2021 2:50 pm
- Forum: Centroid Acorn CNC Controller
- Topic: proLIGHT 2000 Conversion to Acorn
- Replies: 43
- Views: 14919
Re: proLIGHT 2000 Conversion to Acorn
You need to setup your spindle speed in high range pretty accurately FIRST. You can setup for reduction if needed. Look in the Spindle Tab of the Wizard. Hi Marty, The machine only has one spindle range so I'm a bit confused on what to do with the high/mid/low range. The pulley on the motor and spi...
- Sun Feb 14, 2021 10:46 am
- Forum: Centroid Acorn CNC Controller
- Topic: Unable to open nc files (Resolved)
- Replies: 14
- Views: 5834
Re: Unable to open nc files
Sorry for the delayed response guys!
Turns out it was an issue with the USB stick, I switched to another one and the issue went away.
Thanks for the help and sorry for the fire drill!
Turns out it was an issue with the USB stick, I switched to another one and the issue went away.
Thanks for the help and sorry for the fire drill!
- Mon Feb 01, 2021 10:28 am
- Forum: Centroid Acorn CNC Controller
- Topic: Unable to open nc files (Resolved)
- Replies: 14
- Views: 5834
Re: Unable to open nc files
I just attempted to open the file on a 3rd computer as a sanity check and that computer wouldn't even recognize the USB drive. I will try a different flash drive and report back.
- Mon Feb 01, 2021 10:28 am
- Forum: Acorn CNC Tech Tips Knowledge Base, Look Here! before posting
- Topic: Unable to open nc files < run files from USB, copy files from USB automatically>
- Replies: 15
- Views: 8290
Re: Unable to open nc files
I just attempted to open the file on a 3rd computer as a sanity check and that computer wouldn't even recognize the USB drive. I will try a different flash drive and report back.
- Sun Jan 31, 2021 11:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Unable to open nc files (Resolved)
- Replies: 14
- Views: 5834
Unable to open nc files (Resolved)
Hello everyone, Please forgive me if this has been discussed in the past- I used the search function but did not see any relevant results. I am programming in Fusion 360 and used the standard CENTROID fusion post processor. When I try to open the file from my flash drive through CNC12 I get the foll...
- Sun Jan 31, 2021 11:55 pm
- Forum: Acorn CNC Tech Tips Knowledge Base, Look Here! before posting
- Topic: Unable to open nc files < run files from USB, copy files from USB automatically>
- Replies: 15
- Views: 8290
Unable to open nc files < run files from USB, copy files from USB automatically>
Hello everyone, Please forgive me if this has been discussed in the past- I used the search function but did not see any relevant results. I am programming in Fusion 360 and used the standard CENTROID fusion post processor. When I try to open the file from my flash drive through CNC12 I get the foll...