Search found 9 matches
- Fri May 19, 2023 3:04 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Centroid CNC12 v5.04 has been released. Click here to download.
- Replies: 3
- Views: 3428
Re: Centroid CNC12 v5.0 has been released. Click here to download.
Has anyone had any problems with the software installer hanging on windows 10 after selecting "install anyway" in the windows defender popup? I am unable to make it to the pop up to select the control board.
- Tue May 16, 2023 11:03 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: allin1DC controller on 2D eztrak intercon use
- Replies: 3
- Views: 641
Re: allin1DC controller on 2D eztrak intercon use
I also just attached a pic with the line of code that gives me trouble highlighted. I added the parentheses to comment it out.
Thanks again,
Jo
Thanks again,
Jo
- Tue May 16, 2023 10:50 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: allin1DC controller on 2D eztrak intercon use
- Replies: 3
- Views: 641
Re: allin1DC controller on 2D eztrak intercon use
Thanks tblough. Report is attached.
Thanks,
Jon
Thanks,
Jon
- Mon May 15, 2023 9:46 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: allin1DC controller on 2D eztrak intercon use
- Replies: 3
- Views: 641
allin1DC controller on 2D eztrak intercon use
Hi Folks, I am trying to use intercon to generate 2d code for simple cuts. It adds a Z axis home that trips up the software since there is no Z axis. I have been manually commenting out and adding a M00 to allow me to set the quill and/or knee. Is there any work around for this so I don't have to co...
- Thu May 28, 2020 11:17 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Keiling Servos
- Replies: 4
- Views: 1126
Re: Keiling Servos
Hi Marty, The setup is a Bridgeport ez trak (1999 vintage) using the all-in-1 and original servos on x&y with original DC power supply. I believe (but have not tested) the voltage from the original DC rectified 110V power supply is quite a bit higher than the 90V rating keling sells. The thought...
- Thu May 28, 2020 10:52 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Keiling Servos
- Replies: 4
- Views: 1126
Re: Keiling Servos
Marty,
AH! Sorry, all in one controller. The Acorn link was helpful, I can dig around there.
Thanks,
Jon
AH! Sorry, all in one controller. The Acorn link was helpful, I can dig around there.
Thanks,
Jon
- Thu May 28, 2020 9:42 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Keiling Servos
- Replies: 4
- Views: 1126
Keiling Servos
Has anyone worked with keling tech Servos?
Thanks,
JonR
Thanks,
JonR
- Tue May 26, 2020 10:39 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: EZ Trak upgrade from 2 to 3 axis
- Replies: 1
- Views: 730
EZ Trak upgrade from 2 to 3 axis
Good morning, Looking to upgrade my 2 axis EZ track from 2 to 3 axis. I put a centroid all in one on it a couple years ago. I have two questions I couldn't find answers to in the forum: 1. What is the recommended centroid servo torque (or centroid part number) for the typical ballscrew quill set up?...
- Thu Mar 21, 2019 10:37 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Quill scale
- Replies: 3
- Views: 2153
Re: Quill scale
Hi Keith, The GT05-150 scale is still in the bulletin, but not on their website. However, when I contacted them in the last few days, they currently have them, but will be discontinuing it for a "better US made version." A quick additional question: I have an acurite scale on the quill of ...