I don't know if you have found problem or not,
but check jumper J1 VI VR beside control circuit terminals
should be jumper to 1 and 2 for external control
John
Search found 11 matches
- Fri May 24, 2019 1:26 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Huanyang GT Series VFDs
- Replies: 35
- Views: 11360
- Sat May 18, 2019 2:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Probe problem <resolved>
- Replies: 7
- Views: 2423
Re: Probe problem
loaded and running 4-16 all works good , I must have screwed up something in 4-14
Acron what a easy system to set up and run
Acron what a easy system to set up and run
- Fri May 17, 2019 9:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Probe problem <resolved>
- Replies: 7
- Views: 2423
Re: Probe problem
when I look a wizard it shows 6 and 7 set ? 6 probe detect NC, 7 open on contact
what is causing the problem of probe not being disconnect error ?
I have down loaded 4-16 I will try again tomorrow,
Thanks for help
what is causing the problem of probe not being disconnect error ?
I have down loaded 4-16 I will try again tomorrow,
Thanks for help
- Fri May 17, 2019 8:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Probe problem <resolved>
- Replies: 7
- Views: 2423
Re: Probe problem
just a normally closed probe mechanical
- Fri May 17, 2019 5:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Probe problem <resolved>
- Replies: 7
- Views: 2423
Probe problem <resolved>
Was digitizing a part this morning, can up wit an error that probe was jammed , re started and after about 15 mins. had same error, figure I had something set up wrong, so I gave up for today as I had some parts to run, How ever now every time I try to run cutting programs that have been running fin...
- Fri May 03, 2019 10:52 pm
- Forum: Success Stories
- Topic: New to CNC
- Replies: 2
- Views: 2345
New to CNC
My first completed parts, on my design and built cnc , only had drill press and band saw,
being controlled by a great little nut (Acron), first milling of 5 fret boards
being controlled by a great little nut (Acron), first milling of 5 fret boards
- Fri Apr 05, 2019 2:27 pm
- Forum: Centroid Acorn CNC Controller
- Topic: homeing at start up <resolved>
- Replies: 7
- Views: 2708
Re: homeing at start up <resolved>
Thanks Dan ,mine came with relay board, my hook up is like Acron S14984.dwg date 190227 except spindle ok hooked to FC, Mine is 1.5kw 100v, model HY01D511B I'm sure set up is diff. for other models runs great to 24000 rpm with set up below, VI-VR jumper to 1 an 2 PD005=400 PD004=400 PD003=400 PD072=...
- Fri Apr 05, 2019 10:43 am
- Forum: Centroid Acorn CNC Controller
- Topic: homeing at start up <resolved>
- Replies: 7
- Views: 2708
Re: homeing at start up
That was the problem, have had some other problems with things changing , so deleted all , and restarted , all good for now
when I get my Huan Yang going I'll be done
Thanks John
when I get my Huan Yang going I'll be done
Thanks John
- Thu Apr 04, 2019 5:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: homeing at start up <resolved>
- Replies: 7
- Views: 2708
Re: homeing at start up
Thanks I'll go to shop and check, will be later to replay ,no internet in shop
John
John
- Thu Apr 04, 2019 5:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: homeing at start up <resolved>
- Replies: 7
- Views: 2708
homeing at start up <resolved>
what did I do wrong ? when I first set up Acron on my cnc at power up , press cycle start ,machine would move to home limit switches, do its little dance then set read out to all zero's ,now it doesn't move ,but set's read out to zero , I can jog all to home and reset works fine