Search found 34 matches
- Thu Jan 28, 2021 8:12 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Error 907 Z Axis travel exceeded (RESOLVED)
- Replies: 10
- Views: 5348
Re: Error 907 Z Axis travel exceeded
I have attached my mfunc6.mac file. This is the based on the file created by swissi for use with Probeapp / F360. if you look for "MDR" in the comments, you will see the couple changes I made: At the beginning of the macro system variable #4003 is read and saved to user variable #105. Syst...
- Wed Dec 30, 2020 5:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Fusion 360 Mill Post Processor for Acorn with additional Features (New Version 5)
- Replies: 160
- Views: 79099
- Wed Dec 30, 2020 12:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Fusion 360 Mill Post Processor for Acorn with additional Features (New Version 5)
- Replies: 160
- Views: 79099
Re: Fusion 360 Mill Post Processor for Acorn with additional Features (New Version 3)
Coolant: The post creates the following code: (Drill2) (begin job) N110 T148 M6 N115 S4500 M3 N120 G54 N125 M7 N135 G0 X0. Y-0.651 N140 G43 Z0.6 H148 N150 Z0.2 N155 G98 G73 X0. Y-0.651 Z-0.4 R0.2 Q0.126 F18. ..... The coolant command (M7) is created before the rapid, causing the machine to spray coo...
- Wed Dec 30, 2020 11:54 am
- Forum: Centroid Acorn CNC Controller
- Topic: Fusion 360 Mill Post Processor for Acorn with additional Features (New Version 5)
- Replies: 160
- Views: 79099
Re: Fusion 360 Mill Post Processor for Acorn with additional Features (New Version 3)
Check for conflicting Tool Numbers (same Number but different Tools): Logic has been added that checks for conflicting Tool Information e.g. using the same Tool Number but with different geometry. In F360, I have some mill-drills https://www.lakeshorecarbide.com/altincoatedchamferdrill-mills.aspx s...
- Mon Dec 28, 2020 11:10 am
- Forum: Centroid Acorn CNC Controller
- Topic: An easier way to make buttons
- Replies: 6
- Views: 2881
Re: An easier way to make buttons
This post was a favorable mention of the Boxy .svg editor.
It seemed great, it's not.
The .svg files it makes don't play nice with Centriod.
Back to Inscape.
Forget I mentioned it.
It seemed great, it's not.
The .svg files it makes don't play nice with Centriod.
Back to Inscape.
Forget I mentioned it.
- Mon Dec 28, 2020 11:09 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: One-Shot VCP .SVG Buttons
- Replies: 0
- Views: 2517
One-Shot VCP .SVG Buttons
Hi, Wondering if .SVG files for the built in One-Shot functions have been released for public use? I don't see them in the cncm\resources\vcp\Buttons folders. I see that the artwork exists for custom overlays per TB194: https://www.centroidcnc.com/centroid_diy/tech_bulletins/uploads/194.pdf I'm aski...
- Fri Dec 11, 2020 2:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Tool Check Spindle Dwell
- Replies: 1
- Views: 1313
Tool Check Spindle Dwell
I currently have a dwell time programmed into my M3 macro to allow 5 seconds for the spindle to spool up, which works as expected except when resuming from a tool check. When I resume, motion starts immediately after the spindle is energized. If I forget to crank down the feedrate override before I ...
- Wed Dec 09, 2020 9:06 am
- Forum: Centroid Acorn CNC Controller
- Topic: ProbeApp V2: The ultimate solution for Tool Height Offsets
- Replies: 55
- Views: 36495
Re: ProbeApp V2: The ultimate solution for Tool Height Offsets
I did some testing with my Tormach probe and found that approach direction makes a huge difference. If I orient the probe so one of the sides of the probes kinematic “triangle” is in line with the probing axis, then I get +/-.002” repeatability. If I turn the probe 45 degrees, the repeatability dro...
- Tue Dec 08, 2020 10:19 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Error 907 Z Axis travel exceeded (RESOLVED)
- Replies: 10
- Views: 5348
Re: Error 907 Z Axis travel exceeded
I think the problem is that your M6 macro selected "G91" mode (in order to do the "G28 G91 X0 Y0 Z0" move to the tool-change position), but your CNC program assumed that it was still in G90 mode after the M6. Because you end the tool change at maximum Z height and (inadvertently...
- Mon Dec 07, 2020 5:34 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Error 907 Z Axis travel exceeded (RESOLVED)
- Replies: 10
- Views: 5348
Error 907 Z Axis travel exceeded (RESOLVED)
Hi, Trying to run a job, getting the 907 error, can't for the life of me figure out why. I Touched off G54 Z0 using probe (loaded the probe using m6T2H2) When I try to run the following job it throws a error at line N55 when I hit cycle start % (T22 D=0.25 ZMIN=-0.18 - flat end mill - HELICAL - END ...