Thanks Uwe,
I made the change you suggested and tweaked some other settings and the mill is running properly. I appreciate your help.
Curtis
Search found 43 matches
- Mon Nov 07, 2022 5:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Seeking Help with Acorn CNC12 ver 4.80 Wizard Configuration <done>
- Replies: 5
- Views: 722
- Sun Nov 06, 2022 8:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Seeking Help with Acorn CNC12 ver 4.80 Wizard Configuration <done>
- Replies: 5
- Views: 722
Re: Seeking Help with Acorn CNC12 ver 4.80 Wizard Configuration
I replied earlier to your response but for some reason it isn't showing. To answer your question, there is nothing attached to the #5 Input terminal. Only the E-Stop is attached to the input #8 position.
- Sun Nov 06, 2022 8:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Seeking Help with Acorn CNC12 ver 4.80 Wizard Configuration <done>
- Replies: 5
- Views: 722
Re: Seeking Help with Acorn CNC12 ver 4.80 Wizard Configuration
Hi Uwe, If it is any help I followed this attached schematic for wiring my system. It all worked well for several years until I reinstalled Win 10 and Acorn CNC12 ver. 4.80 so I'm assuming the problem is in how I've configured the Wizard. With respect to the Leadshine drives, there is no ENA- connec...
- Sun Nov 06, 2022 4:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Seeking Help with Acorn CNC12 ver 4.80 Wizard Configuration <done>
- Replies: 5
- Views: 722
Seeking Help with Acorn CNC12 ver 4.80 Wizard Configuration <done>
To make a long story short, computer issues necessitated a fresh install of Win10 and Acorn CNC12. I lost the most recent report generated in Acorn CNC12 and had to use an old report which I knew had problems with the Wizard configuration. I've attached the most recent report generated today and scr...
- Mon Jun 04, 2018 3:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Can't Access The Acorn Wizard (Solved)
- Replies: 12
- Views: 4446
Re: Can't Access The Acorn Wizard (Solved)
Marty, I setup the Firewall so it would allow the cncm folder through (by selecting the folder I assumed, incorrectly, it would allow all applications in the folder through). The instructions for this were in one of the videos explaining how to configure Windows 10 for the Acorn board and CNC12. Unf...
- Mon Jun 04, 2018 11:53 am
- Forum: Centroid Acorn CNC Controller
- Topic: Can't Access The Acorn Wizard (Solved)
- Replies: 12
- Views: 4446
Solved: Can't Access Wizard
I found the problem, finally. I was preparing to uninstall and then reinstall CNC12 a second time per Marty's suggestion. I opened CNC12, generated a report, closed CNC12, turned off real time virus protection in Defender and turned off the Windows Firewall. Just to check one more time I opened the ...
- Sun Jun 03, 2018 8:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Can't Access The Acorn Wizard (Solved)
- Replies: 12
- Views: 4446
Re: Can't Access The Acorn Wizard
Marty, Yes to each of your questions. The last time I accessed the Wizard successfully was when I changed the steps/rev values a couple of weeks ago. Just prior to that I had upgraded to ver 4.12 of CNC12 and had repopulated the Wizard with the appropriate values/parameters. At this point CNC12, the...
- Sun Jun 03, 2018 7:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Can't Access The Acorn Wizard (Solved)
- Replies: 12
- Views: 4446
Re: Can't Access The Acorn Wizard
Regenerating the tool offset table got rid of the 907 error. Still unable to access the Wizard. I was able to run the rest of the operations for the part successfully.
CJ
CJ
- Sun Jun 03, 2018 5:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Can't Access The Acorn Wizard (Solved)
- Replies: 12
- Views: 4446
Re: Can't Access The Acorn Wizard
Marty,
Ethernet port 10.168.41.1 and Acorn board 10.168.41.2 passed the ping test.
CJ
Ethernet port 10.168.41.1 and Acorn board 10.168.41.2 passed the ping test.
CJ
- Sun Jun 03, 2018 4:58 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Can't Access The Acorn Wizard (Solved)
- Replies: 12
- Views: 4446
Re: Can't Access The Acorn Wizard
Hi Marty, In my first post I indicated that the appropriate lights were lit up and a “heartbeat” was present on the BBG. The mill was working ok except for a 907 z limit exceeded error. I had completed one operation without problem prior to the 907 error. I wanted to check the value for Z travel in ...