![Smile :)](./images/smilies/icon_e_smile.gif)
Search found 14 matches
- Sun Feb 19, 2023 6:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Mill will not home and erattic behavior from all axis <damaged ethernet cable?>
- Replies: 4
- Views: 637
Re: Mill will not home and erattic behavior from all axis
I did run through all the connections while I had it apart, tightened everything, and inspected solder joints. I didn't take any pics before closing it up. If the problem returns, I will get plenty of pics and pull out what little hair I have. ![Smile :)](./images/smilies/icon_e_smile.gif)
![Smile :)](./images/smilies/icon_e_smile.gif)
- Sun Feb 19, 2023 2:09 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Mill will not home and erattic behavior from all axis <damaged ethernet cable?>
- Replies: 4
- Views: 637
Re: Mill will not home and erattic behavior from all axis
I am back up and running for the moment, I looked in the control box and found the ethernet cable was badly kinked, replaced it, and now it seems to be functioning properly. Fingers crossed it was that simple.
- Sun Feb 19, 2023 11:36 am
- Forum: Centroid Acorn CNC Controller
- Topic: Mill will not home and erattic behavior from all axis <damaged ethernet cable?>
- Replies: 4
- Views: 637
Mill will not home and erattic behavior from all axis <damaged ethernet cable?>
When I turned my mill on and attempted to home the axis the screen showed things were moving, but the steppers did not engage. I tried restarting both the control box and the PC got the same result. When I tried to move the axis from the VCP I was getting simultaneous rough movements from X, Y and Z...
- Mon Apr 27, 2020 8:13 pm
- Forum: Centroid Acorn CNC Controller
- Topic: PM-25MV e-stop
- Replies: 17
- Views: 7024
Re: PM-25MV e-stop
Not sure if you figured out a solution to your estop question. I used a multi pole estop switch that allowed me to run both the mill and controller estops on the same switch. Hopefully this helps
- Sun Jan 05, 2020 12:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: 3 axis automatic probing
- Replies: 9
- Views: 3682
Re: 3 axis automatic probing
Keith, thank you for helping out with the macro . Here is the info you requested. Probe an outside corner from back left, probing in the X first, Y second and Z last, Starting point would be within 1" of the corner and less than 1" from stock top and would like to park the Z at .5 over cor...
- Wed Jan 01, 2020 12:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: 3 axis automatic probing
- Replies: 9
- Views: 3682
Re: 3 axis automatic probing
Keith, I sent you a PM over on FB
- Mon Dec 23, 2019 10:01 pm
- Forum: Centroid Acorn CNC Controller
- Topic: 3 axis automatic probing
- Replies: 9
- Views: 3682
3 axis automatic probing
I recently purchased the digitizing package and found that it will not do X, Y and Z setup probing in one operation. I have seen this done on other systems and was wondering if it was possible with CNC12. I posted this over on the Face Book group page and Keith has offered to write a custom macro fo...
- Fri Mar 15, 2019 8:41 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Touch probe
- Replies: 0
- Views: 1749
Touch probe
Was wondering if there are any changes to touch probe set ups with the current update?
- Sat Apr 14, 2018 5:59 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Software upgrade?
- Replies: 8
- Views: 2861
Re: Software upgrade?
Got it, thank you.
Now how do I install it?
Thanks
Ed
Now how do I install it?
Thanks
Ed
- Fri Apr 13, 2018 10:31 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Software upgrade?
- Replies: 8
- Views: 2861
Re: Software upgrade?
I did that already
Just wondering how long it should take?
Just wondering how long it should take?