Search found 2179 matches
- Tue Apr 16, 2024 8:35 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Trouble creating Air Blast Macro
- Replies: 14
- Views: 299
Re: Trouble creating Air Blast Macro
M68 to activate, M88 to deactivate
- Tue Apr 16, 2024 7:18 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: VCP RESET onscreen button
- Replies: 17
- Views: 513
Re: VCP RESET onscreen button
Installation of beta RC#6 has solved this issue. Thanks for all your replies.
- Mon Apr 15, 2024 6:49 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: VCP RESET onscreen button
- Replies: 17
- Views: 513
Re: VCP RESET onscreen button
I would say that mine (5.08) does not operate that way. Which is what I've been asking for in this thread.
Scott, Keith....
What is the state of the reset button when either the DriveOk or SpindleOk inputs are tripped?
Scott, Keith....
What is the state of the reset button when either the DriveOk or SpindleOk inputs are tripped?
- Mon Apr 15, 2024 3:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: acorn to ahha!
- Replies: 10
- Views: 552
Re: acorn to ahha!
If your drives are 45khtz max, you should reduce the step pulse frequency even farther. The step pulse frequency sets the width (in usec) of the step pulse. For each pulse you will have an equal or greater (depending on speed) void between pulses. For example, at 100khtz this calculates to 1,000,000...
- Sat Apr 13, 2024 1:01 pm
- Forum: Centroid Acorn CNC Controller
- Topic: min lathe build AC spindel on off control
- Replies: 5
- Views: 139
Re: min lathe build AC spindel on off control
Yes. And another set to SpinREV will be controlled by M4 and M5. These are all covered in the manual, it will benefit you to spend some time there.
- Fri Apr 12, 2024 5:26 pm
- Forum: Centroid Acorn CNC Controller
- Topic: min lathe build AC spindel on off control
- Replies: 5
- Views: 139
Re: min lathe build AC spindel on off control
In the wizard, set the output that the motor is connected to as: "SpinFWD"
- Fri Apr 12, 2024 4:47 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: VCP RESET onscreen button
- Replies: 17
- Views: 513
Re: VCP RESET onscreen button
1) Cycle estop does NOT clear reset. Reset must be pressed twice to reactivate NoFault Out 2) I do not want to create any custom buttons 3) These are ClearPath systems using AVID or CNC Depot spindle modules, so neither of those resets re being used Has anyone loaded my report? Something's wierd Her...
- Thu Apr 11, 2024 9:34 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: VCP RESET onscreen button
- Replies: 17
- Views: 513
Re: VCP RESET onscreen button
reading marc's comments i thought he was asking for a virtual estop button which osha isn't going to like. No, not at all. I was suggesting that the appearance of the VCP reset button could change, depending on whether the actual emergency stop button was pressed. This would make it more obvious to...
- Thu Apr 11, 2024 8:18 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help with Z move speed
- Replies: 7
- Views: 135
Re: Help with Z move speed
The Z will perform well straight up on a 5mm pitch ball screw. Adding reduction is overkill
That said, you need more reduction on the x & y. Less than 1 is not recommended
That said, you need more reduction on the x & y. Less than 1 is not recommended
- Thu Apr 11, 2024 7:17 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: VCP RESET onscreen button
- Replies: 17
- Views: 513
Re: VCP RESET onscreen button
the reset button is not an estop. Dont want it to be one. I have physical working estop switches the vcp reset button is resetting software, CNC12, clearing fault messages etc. You forgot that it also toggles the NoFault output when present a virtual 'estop' isn't an actual estop and can not be lab...