Search found 2182 matches
- Wed Apr 17, 2024 9:23 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Beta 5.1 RC#6 DriveOk (Fault) inoperative
- Replies: 4
- Views: 91
- Wed Apr 17, 2024 2:40 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Beta 5.1 RC#6 DriveOk (Fault) inoperative
- Replies: 4
- Views: 91
Re: Beta 5.1 RC#6 DriveOk (Fault) inoperative
This thread can be ignored as 2 errors were found:
1) PICNIC error (problem in chair, not in computer
2) ID 10 T error: ID10T in control.
The reason the Drive Alarm was not active was because the operator was not enabling the motors prior to the test.
1) PICNIC error (problem in chair, not in computer
2) ID 10 T error: ID10T in control.
The reason the Drive Alarm was not active was because the operator was not enabling the motors prior to the test.
- Wed Apr 17, 2024 11:26 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Beta 5.1 RC#6 DriveOk (Fault) inoperative
- Replies: 4
- Views: 91
Beta 5.1 RC#6 DriveOk (Fault) inoperative
Guys... This issue was first noticed in v5.08 release and it has reappeared in this RC #6. After initial install and setup an input (#6 in this case), set to "DriveOk" works as expected for a while, but then stops working. I haven't tried a clean install as I wanted to wait in case there w...
- Tue Apr 16, 2024 8:35 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Trouble creating Air Blast Macro
- Replies: 14
- Views: 284
Re: Trouble creating Air Blast Macro
M68 to activate, M88 to deactivate
- Tue Apr 16, 2024 7:18 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: VCP RESET onscreen button
- Replies: 17
- Views: 483
Re: VCP RESET onscreen button
Installation of beta RC#6 has solved this issue. Thanks for all your replies.
- Mon Apr 15, 2024 6:49 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: VCP RESET onscreen button
- Replies: 17
- Views: 483
Re: VCP RESET onscreen button
I would say that mine (5.08) does not operate that way. Which is what I've been asking for in this thread.
Scott, Keith....
What is the state of the reset button when either the DriveOk or SpindleOk inputs are tripped?
Scott, Keith....
What is the state of the reset button when either the DriveOk or SpindleOk inputs are tripped?
- Mon Apr 15, 2024 3:03 pm
- Forum: Centroid Acorn CNC Controller
- Topic: acorn to ahha!
- Replies: 10
- Views: 548
Re: acorn to ahha!
If your drives are 45khtz max, you should reduce the step pulse frequency even farther. The step pulse frequency sets the width (in usec) of the step pulse. For each pulse you will have an equal or greater (depending on speed) void between pulses. For example, at 100khtz this calculates to 1,000,000...
- Sat Apr 13, 2024 1:01 pm
- Forum: Centroid Acorn CNC Controller
- Topic: min lathe build AC spindel on off control
- Replies: 5
- Views: 138
Re: min lathe build AC spindel on off control
Yes. And another set to SpinREV will be controlled by M4 and M5. These are all covered in the manual, it will benefit you to spend some time there.
- Fri Apr 12, 2024 5:26 pm
- Forum: Centroid Acorn CNC Controller
- Topic: min lathe build AC spindel on off control
- Replies: 5
- Views: 138
Re: min lathe build AC spindel on off control
In the wizard, set the output that the motor is connected to as: "SpinFWD"
- Fri Apr 12, 2024 4:47 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: VCP RESET onscreen button
- Replies: 17
- Views: 483
Re: VCP RESET onscreen button
1) Cycle estop does NOT clear reset. Reset must be pressed twice to reactivate NoFault Out 2) I do not want to create any custom buttons 3) These are ClearPath systems using AVID or CNC Depot spindle modules, so neither of those resets re being used Has anyone loaded my report? Something's wierd Her...