Search found 2210 matches
- Tue May 14, 2024 11:26 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Axis motion after electronics moved to new enclosure
- Replies: 4
- Views: 45
Re: Axis motion after electronics moved to new enclosure
Check the direction wire to the left Y driver
- Mon May 13, 2024 9:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Grizzly G4003G conversion
- Replies: 6
- Views: 104
Re: Grizzly G4003G conversion
Not just 230v, but 230v 3 phase, with a vfd that will accept single phase input. The only way to go, and usually less than a servo
- Sat May 11, 2024 6:39 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 41
- Views: 2379
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
You can measure dc volts on the direction pins, ~5 volts vs ~ a few tenths of a volt for pos vs neg movement, unless inverted. But, you will need a scope to verify step signal
- Thu May 09, 2024 10:20 am
- Forum: Centroid Acorn CNC Controller
- Topic: Help on isolation switch fit two circuits/power supplies
- Replies: 19
- Views: 441
Re: Help on isolation switch fit two circuits/power supplies
Why should I put the vfd in a seperate box I've seen almost all enclosures online with the vfd in the same enclosure. In most cases, I do exactly what you refer to. VFD in the control box. No problems, as I have an oscilloscope, I stock various sizes and types of line reactors, and EMI filters AND ...
- Wed May 08, 2024 8:26 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New Build Steel Frame Router
- Replies: 28
- Views: 623
Re: New Build Steel Frame Router
Slower moves will also accelerate slower. I have to think about why that's a benefit. Of course they do. Feedrate motion is accompanied with cutting, cutting action can seldom tolerate the acceleration that rapids can. Acorn 4 may be a hobby priced package, but make no mistake the Centroid controll...
- Wed May 08, 2024 11:05 am
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrading a Gorilla CNC from Flashcut to Acorn
- Replies: 12
- Views: 274
Re: Upgrading a Gorilla CNC from Flashcut to Acorn
If you look on the Schematics page, you will see numerous examples that both source and sink step/direction signals to stepper drives from the DB25 header. FYI... on the advanced page you have the ability to invert signals. No sense over complicating the process, a bit more time in the manual and on...
- Wed May 08, 2024 10:56 am
- Forum: Centroid Acorn CNC Controller
- Topic: New Build Steel Frame Router
- Replies: 28
- Views: 623
Re: New Build Steel Frame Router
I have not been able to find any documentation on the acceleration setting. Usually acceleration has units of m/s^2 or ft/s^2. In Acorn the unit is in Seconds, so I am guessing that's the time to accelerate to full speed? (Intuitive) Internally there must be a conversion to acceleration m/s^2. If w...
- Tue May 07, 2024 11:39 am
- Forum: Centroid Acorn CNC Controller
- Topic: Help on isolation switch fit two circuits/power supplies
- Replies: 19
- Views: 441
Re: Help on isolation switch fit two circuits/power supplies
A few observations: In my experience, usually the spindle would be on a higher amperage circuit than the control Is there a reason to not use a single, higher amperage circuit? I prefer using a load break switch, usually door mounted as an added safety feature Your spindles VFD and the drives power ...
- Mon May 06, 2024 8:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 Software cycle start disabled
- Replies: 10
- Views: 255
Re: CNC12 Software cycle start disabled
Well said Marc. There is a deep rooted long standing "programmer bias" in the PLC code intentionally set for reasons I cannot wrap my head around. Normally open and closed devices are binary, in other words, as simply as any actionable device can be. 2 choices, represented as zero or one. ...
- Sat May 04, 2024 6:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: ethernet communication errors...wits end
- Replies: 8
- Views: 258
Re: ethernet communication errors...wits end
Go to the LAN adapters mfgr website and update the driver(s)