Search found 47 matches
- Thu Feb 08, 2024 12:35 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Digitising Issues CNC12 5.06
- Replies: 6
- Views: 345
Re: Digitising Issues CNC12 5.06
PROBLEM RESOLVED None of the suggested fixes worked... However, by reducing the Axis Step, I was able to successfully probe the contour. My original step value was set to 2mm - in desperation I reduced it to 0.5mm and the contour digitise worked fine. To speed up the process the Axis Step was increa...
- Sun Feb 04, 2024 8:26 am
- Forum: Centroid Acorn CNC Controller
- Topic: Digitising Issues CNC12 5.06
- Replies: 6
- Views: 345
Re: Digitising Issues CNC12 5.06
Hello CNCSNW
Thanks for the suggestion.
I will try starting in in the lower left quadrant positioned as you said and work my around all four quadrants.
Also going to increase the patch size as Keith suggested
[/quote]
Thanks for the suggestion.
I will try starting in in the lower left quadrant positioned as you said and work my around all four quadrants.
Also going to increase the patch size as Keith suggested
[/quote]
- Sun Feb 04, 2024 8:19 am
- Forum: Centroid Acorn CNC Controller
- Topic: Digitising Issues CNC12 5.06
- Replies: 6
- Views: 345
- Sun Feb 04, 2024 8:12 am
- Forum: Centroid Acorn CNC Controller
- Topic: Digitising Issues CNC12 5.06
- Replies: 6
- Views: 345
Re: Digitising Issues CNC12 5.06
Hello CNCSNW I tried starting in in the lower left quadrant positioned as you said - no joy. Next upper left quadrant - still not working Tried all 4 quadrants to no avail. increased the patch size as Keith suggested his reply - no luck here either The only thing I haven't tried is reducing the step...
- Sat Feb 03, 2024 2:40 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Turning a radius on a lathe
- Replies: 1
- Views: 199
Re: Turning a radius on a lathe
Hello Phil,
Please post a drawing.
Please post a drawing.
- Sat Feb 03, 2024 2:35 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Digitising Issues CNC12 5.06
- Replies: 6
- Views: 345
Digitising Issues CNC12 5.06
I recently updated my mill to CNC12 5.06 No Problems other than Contour Digitising All probing cycles are working as expected. I calibrated my probe using a 25 mm Ring Gauge and tested the following cycles: Bores, Boss, Slot, Web, Inside and Outside corner etc all fine. I want to route out a panel t...
- Sun Jan 21, 2024 7:19 am
- Forum: Centroid Acorn CNC Controller
- Topic: WMPG Shared between two machines
- Replies: 2
- Views: 295
Re: WMPG Shared between two machines
Hello, The simple way to share WMPG is switch the USB lead from one CNC PC to the other PC. You need to switch the USB lead before starting CNC 12. To save constant switching of leads - get a USB switchover device - preferably a simple mechanical one if you can find one. (These used to be common for...
- Thu Nov 30, 2023 6:12 am
- Forum: Centroid Acorn CNC Controller
- Topic: PWM for Laser on Rev 2 Acorn Board
- Replies: 10
- Views: 1902
Re: PWM for Laser on Rev 2 Acorn Board
Happy to report that laser is now operational!
Thanks again to all for your help.
Thanks again to all for your help.
- Mon Nov 27, 2023 5:29 am
- Forum: Centroid Acorn CNC Controller
- Topic: PWM for Laser on Rev 2 Acorn Board
- Replies: 10
- Views: 1902
Re: PWM for Laser on Rev 2 Acorn Board
Thanks to all who have helped me with this project - I now have a laser on my Mill with Acorn Rev 2 board!
Special thanks to suntravel for the inspiration and pointed me in the right direction and tblough for reminding me of the importance of reading the drawing!
Special thanks to suntravel for the inspiration and pointed me in the right direction and tblough for reminding me of the importance of reading the drawing!
- Sat Nov 25, 2023 7:27 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn with Lasertree K40
- Replies: 8
- Views: 996
Re: Acorn with Lasertree K40
Thank you - did not see that in the literature or schematic.
I set this up tomorrow.
I set this up tomorrow.