Search found 27 matches

by Centroid188
Mon Jan 08, 2024 9:29 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: TWCS
Replies: 1
Views: 1853

Re: TWCS

Our TWCS is only designed for our Rotating head design and table parallel to the X axis. You can still do five axis work without TWCS, your cad / cam package would need to handle the TWCS.. If you are doing 5 axis simultaneous moves you would need the Ultimate Plus software.
by Centroid188
Wed Dec 27, 2023 9:17 am
Forum: Centroid Acorn CNC Controller
Topic: Ether1616 Output boards?
Replies: 2
Views: 393

Re: Ether1616 Output boards?

As long as you do not need the outputs you can leave the relay modules disconnected..
by Centroid188
Wed Dec 13, 2023 11:58 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Drive Fault Conditions
Replies: 7
Views: 4842

Re: Drive Fault Conditions

The drive fault means the drive is giving the control a drive fault message.. Which is the fault in pin on the drive header. The pin connections to the drive are shown on page 36 of the oak install manual, these are not user or PLC definable... https://www.centroidcnc.com/downloads/centroid_Oak_inst...
by Centroid188
Tue Oct 31, 2023 1:26 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: 412 Encoder error - looking for clarification
Replies: 4
Views: 715

Re: 412 Encoder error - looking for clarification

If you set parameter 348 to 0 the MPG encoder error will go away. You also have drive faults and quadrature encoder errors for the Y axis. So you need to make sure the drive is not really in a fault. Then check your cabling. Is the drive set to output Quadrature encoder signals to the control. The p...
by Centroid188
Tue Sep 26, 2023 8:08 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Encoder Expansion - ALLin1DC
Replies: 5
Views: 4074

Re: Encoder Expansion - ALLin1DC

Actually if you put DC encoders directly on the ballscrew you do not need encoders on the motors with the ALLINONEDC. This is the exact solution our Hardinge CHNC / HNC kits use..
by Centroid188
Fri Aug 18, 2023 7:59 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: M400S Will Not Power Up
Replies: 1
Views: 2421

Re: M400S Will Not Power Up

There are tech bulletins on how to do this at:
https://centroidcnc.com/centroid_diy/te ... browse.php
You need your motherboard type.
by Centroid188
Thu Aug 10, 2023 1:40 pm
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: 404 Spindle Drive Fault
Replies: 7
Views: 3099

Re: 404 Spindle Drive Fault

You need to extend the decel time in the spindle inverter. Parameter 0-13.
Your inverter is most likely getting weak since it is older.
There is a Tech Bull # 183 on programming the Delta VFD-V
https://www.centroidcnc.com/dealersuppo ... ds/183.pdf
by Centroid188
Wed Jul 26, 2023 8:29 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Centroid 412 mpg1 encoder error
Replies: 12
Views: 1121

Re: Centroid 412 mpg1 encoder error

Based on the info that no axis will jog. Do you have power to the VM terminals on the allinonedc? Is it between 100 ~ 165 VDC?
by Centroid188
Fri Jun 30, 2023 10:47 am
Forum: Centroid Hickory CNC Controller
Topic: The Hickory CNC controller is now available.
Replies: 33
Views: 25366

Re: The Hickory CNC controller is now available.

The sgdv drives with the ethercat option module OCA01A are not currently supported.
by Centroid188
Tue Jun 27, 2023 8:39 am
Forum: Centroid Acorn CNC Controller
Topic: Homing 4th Axis issue
Replies: 7
Views: 569

Re: Homing 4th Axis issue

The report shows the 4th axis setup as input 2 which is home the slaved axis.
The way you described it you want it to be input 3 homeall with the other axis.
That is most likely the issue..