Search found 34 matches
- Fri Feb 10, 2023 5:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Xkeys USB Keypad Operator Control Panel for Centroid CNC
- Replies: 14
- Views: 2896
Re: Xkeys USB Keypad Operator Control Panel for Centroid CNC
The image files are for labeling the keys as you have already done. The Legends are not for labeling the buttons when you are in macroworks. If a key is programmed there will be a blue Check, if not programmed it will be blank. I have never seen nor attempted to have images on the buttons when in Ma...
- Mon Oct 17, 2022 12:38 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
- Replies: 9
- Views: 1452
Re: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
Once I get things working....
The only issue to be resolved is the DriveOk signal from the V1000 to the Acorn. The status on the Input/Output panel (Alt-i) is always red.
The only issue to be resolved is the DriveOk signal from the V1000 to the Acorn. The status on the Input/Output panel (Alt-i) is always red.
- Mon Oct 17, 2022 11:37 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
- Replies: 9
- Views: 1452
Re: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
Digging deeply into the Yaskawa information, the jumper needs to be in place or a safety switch needs to be placed across the terminals.
- Wed Oct 05, 2022 8:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG Problems
- Replies: 34
- Views: 12056
Re: Wireless MPG Problems
Nope, going to try it on another machine, if the problem follows the MPG then we will look in that direction...
I think at this point the proximity of the two antennas is likely the issue. We will see.
Beevo
I think at this point the proximity of the two antennas is likely the issue. We will see.
Beevo
- Wed Oct 05, 2022 5:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG Problems
- Replies: 34
- Views: 12056
Re: Wireless MPG Problems
I thought I had it whipped when I switched back to the disposable alkaline batteries, because of the lower operating voltage. No such luck. The only issue is this is extremely intermittent. I will try to capture this goofiness. Anything specific you want to see outside of the dial being turned and t...
- Wed Oct 05, 2022 1:35 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG Problems
- Replies: 34
- Views: 12056
Re: Wireless MPG Problems
I am coming to this party very late... I have had issues with the Wireless MPG exhibiting the same issues from time to time. It is very intermittent in nature. I was searching the forums for something else and after a period of time stumbled on this post. You will be turning the knob at an even cons...
- Fri Sep 30, 2022 9:25 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
- Replies: 9
- Views: 1452
Re: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
I am following the Centroid diagram to the letter. It does not show the jumper.
- Fri Sep 30, 2022 1:29 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
- Replies: 9
- Views: 1452
Re: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
OK, everything went well with the tuning and no load operation of the spindle seems fine. The rest of the controls are still a work in progress. I attempted to test some of this bu feeding 5vdc into the unit, no spindle run though. I am wondering if I have to deal with VFD Reset and Spindle OK input...
- Mon Sep 05, 2022 5:58 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
- Replies: 9
- Views: 1452
Re: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
I guessed, not expected. A lot of this is black magic to me. LOL
I appreciate the input!!
I appreciate the input!!
- Mon Sep 05, 2022 4:59 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
- Replies: 9
- Views: 1452
Yaskawa V1000 and Mitsubishi SJ-N SPindle motor
I am currently at the point where I need to tune the VFD I am using on a 5hp slant bed lathe. VFD: Yaskawa V1000 20220905_132931_std.jpg Motor: Mitsubishi Motor Plate.JPG The fun begins with the information that I need to enter based on "how to tune yer motor" video found online. The scree...