Search found 6691 matches

by martyscncgarage
Fri Dec 04, 2020 10:50 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Drawbar Proximity Switches
Replies: 2
Views: 16

Re: Drawbar Proximity Switches

Hi all, I'm having a hard time getting the correct I/O states for my drawbar proximity switches when doing tool changes. Ive tried inverting them and forcing others. What I have is 3 proximity switches at 3 differing heights: Clamped, Unclamped, and Tool Release. Just wondering what CNC 12 is looki...
by martyscncgarage
Fri Dec 04, 2020 10:40 am
Forum: Centroid Acorn CNC Controller
Topic: Chinese Tool Touch off and a Probe Calibration
Replies: 3
Views: 32

Re: Chinese Tool Touch off and a Probe Calibration

Take the time to read the Centroid Probe Setup Guide:
https://www.centroidcnc.com/centroid_di ... _setup.pdf

Consider Swissi's Probe App:
viewtopic.php?f=60&t=4973

Marty
by martyscncgarage
Fri Dec 04, 2020 10:38 am
Forum: Centroid Acorn CNC Controller
Topic: Hardinge AHC Accuslide Acorn Conversion
Replies: 13
Views: 139

Re: Hardinge AHC Accuslide Acorn Conversion

Single: USB 3.0 Male to USB 3.0 Female AUX Flush Mount Car Mount Extension Cable for Car Truck Boat Motorcycle Dashboard Panel -(3 Feet - 1 Meter) by ExcellentConcept Learn more: https://www.amazon.com/dp/B01NAMU8KY/ref=cm_sw_em_r_mt_dp_yKKYFbSHKX5V8?_encoding=UTF8&psc=1 Double: 2 Ports Dual USB...
by martyscncgarage
Fri Dec 04, 2020 9:00 am
Forum: Centroid Acorn CNC Controller
Topic: Hardinge AHC Accuslide Acorn Conversion
Replies: 13
Views: 139

Re: Hardinge AHC Accuslide Acorn Conversion

Consider a USB bulkhead connector for your cabinet so you have external access to the USB ports.
Can be found on Amazon
by martyscncgarage
Thu Dec 03, 2020 2:44 pm
Forum: Centroid Acorn CNC Controller
Topic: Optiturn 2506 conversion.
Replies: 8
Views: 173

Re: Optiturn 2506 conversion.

Hello b_laauwen, If you're looking at using a KB speed control for your project, take a look at the KBCC-125R unit. It combines an "anti-plug" reversing relay", a heat Sink and dynamic braking resistor all in one package for 1.5 HP (120v) and 3.0 HP (240v) PM or shunt wound DC motors...
by martyscncgarage
Thu Dec 03, 2020 2:42 pm
Forum: Centroid Acorn CNC Controller
Topic: Control Cabinet Inlet Fan
Replies: 15
Views: 157

Re: Control Cabinet Inlet Fan

I put 3/4" plastic spacers around the fan opening, with a bridge running diagonally across to hold the cover stud. The screws that hold the spacers in place also secure the fan inside the door. I tap the corner holes in the fan: 10-32 on an english cabinet, or M5 on a metric cabinet. The plast...
by martyscncgarage
Thu Dec 03, 2020 12:16 pm
Forum: Centroid Acorn CNC Controller
Topic: *** 12/3/20: SITE RESTORED ***
Replies: 0
Views: 38

*** 12/3/20: SITE RESTORED ***

As of this morning it appears email notifications are working again on the forums.

If anyone notices anything out of the ordinary, please post here.
by martyscncgarage
Thu Dec 03, 2020 10:36 am
Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
Topic: Alarm code 549
Replies: 5
Views: 40

Re: Alarm code 549

How about posting the program in question....
by martyscncgarage
Thu Dec 03, 2020 10:33 am
Forum: Centroid Acorn CNC Controller
Topic: Control Cabinet Inlet Fan
Replies: 15
Views: 157

Re: Control Cabinet Inlet Fan

NAPA 2906 crossed over to WIX 42906 WIX Filters - 42906 Air Filter, Pack of 1 by Amazon.com Learn more: https://www.amazon.com/dp/B000C9WK9S/ref=cm_sw_em_r_mt_dp_jBpYFbGM3SH5X Thanks for sharing that Marc. I have used them too. Would like to see how you modified the door. I typically cut two half ci...