probably trying to command a G1 with an encoder installed
read up on G98 and G99 in the operator manual
but who knows i left my crystal ball at home.
Search found 7319 matches
- Tue Apr 23, 2024 6:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn won't run g code/mdi < lathe G98/G99?>
- Replies: 4
- Views: 94
- Tue Apr 23, 2024 6:09 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: processing error
- Replies: 1
- Views: 44
Re: processing error
i moved this post out of the acorn forum into this forum
- Tue Apr 23, 2024 6:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 24
- Views: 454
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
Keith The delta drive is to factory reset. Load the number (gain button section ) start cnc12. try to move the axe , it move very fast ,reverse the movement and the drive stop . drive show Al009 did it run away or just move very fast? what is the delta gear ratio set to? sounds like this is not set...
- Tue Apr 23, 2024 6:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 24
- Views: 454
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
can you swap out a known working drive? to try to isolate the issue. same with cables.
or put this problem drive on the know working system? etc..
divide and conquer to isolate the issue one component at time. SOP debug methodology.
or put this problem drive on the know working system? etc..
divide and conquer to isolate the issue one component at time. SOP debug methodology.
- Tue Apr 23, 2024 6:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: mfunc6 disappearing after restarting CNC12
- Replies: 2
- Views: 5
Re: mfunc6 disappearing after restarting CNC12
post a fresh report.zip so we can see what version you are running and the rest of your setup.
- Tue Apr 23, 2024 2:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New pc works but won't at same time <resolved>
- Replies: 3
- Views: 73
Re: New pc works but won't at same time
yes, massive amount of updates since v4.5 and they are free. read the extensive release notes here in the legacy software section at the bottom of the screen. https://www.centroidcnc.com/centroid_diy/centroid_cnc_software_downloads.html if you decide to install the latest version of CNC12 be sure to...
- Tue Apr 23, 2024 1:59 am
- Forum: Centroid Acorn CNC Controller
- Topic: Board standoffs ?and my drivers arent listed?
- Replies: 10
- Views: 190
Re: Board standoffs ?and my drivers arent listed?
db25 is for stepper drives
screw terminal are for AC Servo drives.
ENA is enable signal. which enables the drives. (tells it to power the motors)
screw terminal are for AC Servo drives.
ENA is enable signal. which enables the drives. (tells it to power the motors)
- Tue Apr 23, 2024 1:58 am
- Forum: Centroid Acorn CNC Controller
- Topic: New pc works but won't at same time <resolved>
- Replies: 3
- Views: 73
Re: New pc works but won't at same time
easiest way to switch to a new PC is
1.) prep the new PC for CNC use following Tb309
2.) Copy the CNCM or CNCT folder from the old PC to the NEW PC.
Done.
1.) prep the new PC for CNC use following Tb309
2.) Copy the CNCM or CNCT folder from the old PC to the NEW PC.
Done.
- Mon Apr 22, 2024 5:49 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: V5.1 Lathe ATC has vanished
- Replies: 3
- Views: 80
Re: V5.1 Lathe ATC has vanished
all your issues are from
intended work flow is: you must use write settings to cnc control at least once before moving the custom tool change slider to YES. we will make this more clear in the next version.
intended work flow is: you must use write settings to cnc control at least once before moving the custom tool change slider to YES. we will make this more clear in the next version.
- Mon Apr 22, 2024 3:18 pm
- Forum: Centroid Acorn CNC Controller
- Topic: GS2 VFD problem
- Replies: 8
- Views: 211
Re: GS2 VFD problem
you have to calibrate the vfd to match the commanded.pescadoman wrote: ↑Sun Apr 21, 2024 3:04 pm And the encoder feedback for the spindle doesn't match the S command rpm...