Search found 8338 matches
- Fri Feb 07, 2025 3:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Geckodrive g320x
- Replies: 79
- Views: 7037
Re: Acorn Geckodrive g320x
ok, now we are at a good baseline. the disk images show that this is classic Lost Motion. with the machine off put your hand on the screw turn the screw 1/8th - 1/4 of a turn CW then CCW, back and forth. you will feel the 'lost motion' you will be able to rotate the screw for a number of degrees tha...
This post has been liked 1 time(s).
- Fri Feb 07, 2025 5:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Geckodrive g320x
- Replies: 79
- Views: 7037
Re: Acorn Geckodrive g320x
post the g code program you are using for the images!
This post has been liked 0 time(s).
- Fri Feb 07, 2025 5:35 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Geckodrive g320x
- Replies: 79
- Views: 7037
Re: Acorn Geckodrive g320x
loose motor or screw pulley?
loose Motor encoder?
drive not working with encoder feedback?
loose Motor encoder?
drive not working with encoder feedback?
This post has been liked 0 time(s).
- Fri Feb 07, 2025 3:43 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Deckel fP4A Dialog11
- Replies: 8
- Views: 675
Re: Deckel fP4A Dialog11
seriously though. I did one of these machines about 10 years ago and went thru all the effort of updating the encoders (building adapters and covers and cables) and using the centroid AC/DC drive to run the big old siemens servos. I would not do that again, too much time and money and still have old...
This post has been liked 0 time(s).
- Fri Feb 07, 2025 3:38 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Deckel fP4A Dialog11
- Replies: 8
- Views: 675
Re: Deckel fP4A Dialog11
i heard rube goldberg has done one of these.
This post has been liked 0 time(s).
- Thu Feb 06, 2025 8:28 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Geckodrive g320x
- Replies: 79
- Views: 7037
Re: Acorn Geckodrive g320x
i am asking you to set the values to 8
put 0.000 in for all backlash compensation
and make a test cut.
put 0.000 in for all backlash compensation
and make a test cut.
This post has been liked 0 time(s).
- Thu Feb 06, 2025 7:38 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Geckodrive g320x
- Replies: 79
- Views: 7037
Re: Acorn Geckodrive g320x
you are mixing two different things together. overall turns ratio does not solve mechanical backlash. by changing the overall turns ratio you are making things worse at this point. leave the numbers at 8 do not adjust them. now figure out where the backlash is coming from. it is Large so it should b...
This post has been liked 0 time(s).
- Thu Feb 06, 2025 5:20 pm
- Forum: Acorn CNC Tech Tips Knowledge Base, Look Here! before posting
- Topic: Quick Tip: IF you have Home/Limit Switches, here is an example and description on setting them up
- Replies: 71
- Views: 130391
Re: Quick Tip: IF you have Home/Limit Switches, here is an example and description on setting them up
with the addition of "HomeLimit" inputs in the Acorn Wizard, this allows a single switch to act as both a limit and home switch just like oak/allin1dc also you can now have a dedicated limit switch inside of a home switch (a limit "protecting" a home switch) with Acorn as well. a...
This post has been liked 0 time(s).
- Thu Feb 06, 2025 4:09 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn Geckodrive g320x
- Replies: 79
- Views: 7037
Re: Acorn Geckodrive g320x
set the X and Y overall turns ratio to 8.000000
This post has been liked 0 time(s).
- Thu Feb 06, 2025 4:08 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Spindle analog output low voltage
- Replies: 10
- Views: 1205
Re: Spindle analog output low voltage
Is there any settings and or parameters that maybe causing this voltage problem? Ill have to double check the wiring again to see if Im missing something, as far as output to the VFD I just have forward and reverse and obviously the analog out and com. if cnc12 thinks there is a touch probe plugged...
This post has been liked 0 time(s).