Search found 7322 matches
- Tue Apr 23, 2024 6:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Centroid acorn router machine build
- Replies: 14
- Views: 698
Re: Centroid acorn router machine build
sorry i can't give this kind of advice, it is up to you to determine the proper amp ratings of wire, contactors, disconnects, relays etc.. usually the VFD manual will tell you what and how to size wire fuses/breakers etc and there are plenty of VFD videos on line. the safety aspect of the project is...
- Tue Apr 23, 2024 6:17 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Hybrid stepper motor error
- Replies: 3
- Views: 95
Re: Hybrid stepper motor error
sounds like the driver is faulting out and releasing power, check for binding/load on motor when holding position and or force that would cause it to be pushed off the commanded hold position. does the drive have a LED that indicates a fault?
- Tue Apr 23, 2024 6:15 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acornsix yaskawa sigma2 issue!
- Replies: 19
- Views: 484
Re: Acornsix yaskawa sigma2 issue!
running in one direction is usually a wiring error
- Tue Apr 23, 2024 6:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn won't run g code/mdi < lathe G98/G99?>
- Replies: 4
- Views: 112
Re: Acorn won't run g code/mdi
probably trying to command a G1 with an encoder installed
read up on G98 and G99 in the operator manual
but who knows i left my crystal ball at home.
read up on G98 and G99 in the operator manual
but who knows i left my crystal ball at home.
- Tue Apr 23, 2024 6:09 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: processing error
- Replies: 1
- Views: 60
Re: processing error
i moved this post out of the acorn forum into this forum
- Tue Apr 23, 2024 6:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 25
- Views: 483
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
Keith The delta drive is to factory reset. Load the number (gain button section ) start cnc12. try to move the axe , it move very fast ,reverse the movement and the drive stop . drive show Al009 did it run away or just move very fast? what is the delta gear ratio set to? sounds like this is not set...
- Tue Apr 23, 2024 6:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 25
- Views: 483
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
can you swap out a known working drive? to try to isolate the issue. same with cables.
or put this problem drive on the know working system? etc..
divide and conquer to isolate the issue one component at time. SOP debug methodology.
or put this problem drive on the know working system? etc..
divide and conquer to isolate the issue one component at time. SOP debug methodology.
- Tue Apr 23, 2024 6:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: mfunc6 disappearing after restarting CNC12
- Replies: 3
- Views: 41
Re: mfunc6 disappearing after restarting CNC12
post a fresh report.zip so we can see what version you are running and the rest of your setup.
- Tue Apr 23, 2024 2:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New pc works but won't at same time <resolved>
- Replies: 3
- Views: 84
Re: New pc works but won't at same time
yes, massive amount of updates since v4.5 and they are free. read the extensive release notes here in the legacy software section at the bottom of the screen. https://www.centroidcnc.com/centroid_diy/centroid_cnc_software_downloads.html if you decide to install the latest version of CNC12 be sure to...
- Tue Apr 23, 2024 1:59 am
- Forum: Centroid Acorn CNC Controller
- Topic: Board standoffs ?and my drivers arent listed?
- Replies: 10
- Views: 205
Re: Board standoffs ?and my drivers arent listed?
db25 is for stepper drives
screw terminal are for AC Servo drives.
ENA is enable signal. which enables the drives. (tells it to power the motors)
screw terminal are for AC Servo drives.
ENA is enable signal. which enables the drives. (tells it to power the motors)