these drives should probably be connected to the DB25
do you have link to the manual for these drives?
Search found 7464 matches
- Fri May 31, 2024 4:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 12
- Views: 161
- Fri May 31, 2024 4:24 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Replacement Ethernet components
- Replies: 5
- Views: 145
Re: Replacement Ethernet components
I’d say your electrician owes you a new acorn system. The switch is maybe $20 the cost of the ether1616 board, I can understand them not wanting to break up prebuilt kits. I know it is a pain, but I’d say you need to buy an entirely new kit. The risk is that you fry each additional component you ad...
- Fri May 31, 2024 4:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Replacement Ethernet components
- Replies: 5
- Views: 145
Re: Replacement Ethernet components
flashing (aka debricking, aka bootloader) instructions are on the Acorn start here page.
https://www.centroidcnc.com/centroid_di ... guide.html
https://www.centroidcnc.com/centroid_di ... guide.html
- Fri May 31, 2024 4:20 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Replacement Ethernet components
- Replies: 5
- Views: 145
Re: Replacement Ethernet components
the glue is there to stop you from plugging anything into it.
- Fri May 31, 2024 3:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rough Motion on Circular Toolpaths
- Replies: 54
- Views: 1398
Re: Rough Motion on Circular Toolpaths
remind me did these drives have drive tuning software?
and you could try messing with delta v max but, you might be going down a rabbit hole with that one.
https://centroidcncforum.com/viewtopic. ... 707#p82707
and you could try messing with delta v max but, you might be going down a rabbit hole with that one.
https://centroidcncforum.com/viewtopic. ... 707#p82707
- Fri May 31, 2024 3:25 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rough Motion on Circular Toolpaths
- Replies: 54
- Views: 1398
Re: Rough Motion on Circular Toolpaths
trying a different pc is just a basic debug technique to quickly eliminate the PC as a possible source of an issue. i carry spare $150 PC's with me just for this purpose, that way i don't have to spend hours/days working on someone else's PC to try and solve an issue. :-) its probably not the PC BUT...
- Fri May 31, 2024 10:10 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: Cycle Start programmatically
- Replies: 3
- Views: 119
- Fri May 31, 2024 10:00 am
- Forum: Centroid Acorn CNC Controller
- Topic: No signal from Acorn to the stepper drivers
- Replies: 12
- Views: 161
Re: No signal from Acorn to the stepper drivers
- Run the PC Tuner on the PC , and then run the stress test.
https://www.centroidcnc.com/centroid_di ... loads.html
- and make a photo album with the requested info so we can help you out.
https://www.centroidcnc.com/centroid_di ... loads.html
- and make a photo album with the requested info so we can help you out.
- Thu May 30, 2024 12:08 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Finally did a fresh install and WPMG still not being recognized by windows
- Replies: 19
- Views: 387
Re: Finally did a fresh install and WPMG still not being recognized by windows
battery type makes a difference as well. don't use rechargeable batteries.
- Thu May 30, 2024 10:25 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Feature Request - SSV
- Replies: 33
- Views: 2619
Re: Feature Request - SSV
Canned SSV has been committed and will be in the next release of CNC12 CNC12 parameters for SSV P981 : Time for Spindle Speed Variation to complete a Full Cycle in Seconds. P982 : Amount of Speed Variation (Example; S = 500, P = 100, Speed would be 400 or 600 depending on where its at in the cycle)....