Right on!
Right now we have not tested a C2000 yet on the Ethercat daisy chain, but will be testing a Delta M300 via as soon as they ship it to us.
Search found 7325 matches
- Wed Apr 24, 2024 6:33 pm
- Forum: Centroid Hickory CNC Controller
- Topic: Kitamura Mycenter Zero - DELTA Ethercat Retrofit
- Replies: 2
- Views: 31
- Wed Apr 24, 2024 5:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Homebuilt tool touchoff block(resolved)
- Replies: 5
- Views: 80
- Wed Apr 24, 2024 5:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 27
- Views: 541
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
Al009 just means the position error exceeds what is set (i believe it is normally 60k pulses; look in the manual; it is some a parameter). This generally happens if the drive is not tuned and/or it is put under recessive stress where it does not have enough power to overcome that. You can monitor i...
- Tue Apr 23, 2024 6:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Centroid acorn router machine build
- Replies: 14
- Views: 717
Re: Centroid acorn router machine build
sorry i can't give this kind of advice, it is up to you to determine the proper amp ratings of wire, contactors, disconnects, relays etc.. usually the VFD manual will tell you what and how to size wire fuses/breakers etc and there are plenty of VFD videos on line. the safety aspect of the project is...
- Tue Apr 23, 2024 6:17 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Hybrid stepper motor error
- Replies: 3
- Views: 112
Re: Hybrid stepper motor error
sounds like the driver is faulting out and releasing power, check for binding/load on motor when holding position and or force that would cause it to be pushed off the commanded hold position. does the drive have a LED that indicates a fault?
- Tue Apr 23, 2024 6:15 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acornsix yaskawa sigma2 issue!
- Replies: 19
- Views: 503
Re: Acornsix yaskawa sigma2 issue!
running in one direction is usually a wiring error
- Tue Apr 23, 2024 6:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn won't run g code/mdi < lathe G98/G99?>
- Replies: 4
- Views: 130
Re: Acorn won't run g code/mdi
probably trying to command a G1 with an encoder installed
read up on G98 and G99 in the operator manual
but who knows i left my crystal ball at home.
read up on G98 and G99 in the operator manual
but who knows i left my crystal ball at home.
- Tue Apr 23, 2024 6:09 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: processing error
- Replies: 1
- Views: 71
Re: processing error
i moved this post out of the acorn forum into this forum
- Tue Apr 23, 2024 6:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 27
- Views: 541
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
Keith The delta drive is to factory reset. Load the number (gain button section ) start cnc12. try to move the axe , it move very fast ,reverse the movement and the drive stop . drive show Al009 did it run away or just move very fast? what is the delta gear ratio set to? sounds like this is not set...
- Tue Apr 23, 2024 6:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 27
- Views: 541
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
can you swap out a known working drive? to try to isolate the issue. same with cables.
or put this problem drive on the know working system? etc..
divide and conquer to isolate the issue one component at time. SOP debug methodology.
or put this problem drive on the know working system? etc..
divide and conquer to isolate the issue one component at time. SOP debug methodology.