Search found 7416 matches
- Wed Jan 21, 2015 1:41 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Mold Magic Version will not load on Win7
- Replies: 4
- Views: 3404
Re: Mold Magic Version will not load on Win7
mold magic runs on XP only. some guys will buy an old running xp machine on ebay just to run it, but mostly they pick up a new cad/cam system to do that kind of work. mold magic has been displaced by affordable 3D cad/cam systems such as vectric aspire and bob cad cam. (Aspire will accept a centroid...
- Thu Jan 15, 2015 8:28 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: issue with limit switch
- Replies: 3
- Views: 2965
Re: issue with limit switch
whenever you switch directions on an axis you have to also switch the limit switches as well. you can do this in the limit switch input setup screen. I can send you a screenshot tomorrow I'm away from my computer right now.
- Mon Jan 12, 2015 11:05 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Cmos Battery dead
- Replies: 3
- Views: 3217
- Mon Jan 12, 2015 11:01 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: RESOLVED- motor backshaft. parts removal? 2K encoder hopes.
- Replies: 2
- Views: 2654
- Mon Jan 12, 2015 11:01 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: RESOLVED- motor backshaft. parts removal? 2K encoder hopes.
- Replies: 2
- Views: 2654
Re: motor backshaft Q. parts removal? 2K encoder hopes.
remove the resolver/tach down to bare shaft, measure shaft, purchase encoder with same diameter hole, drill tap two mounting holes, mount new encoder, connect connector to cable. done. here is link to photo album showing a different more complicated encoder install.. i think you will get the idea. h...
- Sun Jan 11, 2015 4:21 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Ajax DM45 - Angular Bearing Nut
- Replies: 2
- Views: 2655
Re: Ajax DM45 - Angular Bearing Nut
First you want to isolate the lash. where is it coming from exactly? nut to screw? screw to table? nut mount to table? etc... once you have found where the lash is actually coming from only then would you adjust the nut tension on the end of the ballscrew. for your questions.. a great resource is th...
- Sun Jan 11, 2015 4:12 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: MPG is not working in MDI
- Replies: 1
- Views: 2151
Re: MPG is not working in MDI
you can change the plc program to allow the mpg to be active in MDI mode. typically this is not a good idea..but as long as you know thats the way your machine is configured...
drop an email to tech@ajaxcnc.com and they will let you know how to make the change.
drop an email to tech@ajaxcnc.com and they will let you know how to make the change.
- Tue Dec 02, 2014 8:31 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Spindle Motor for Bridgeport Series 2 Interact II
- Replies: 5
- Views: 4353
Re: Spindle Motor for Bridgeport Series 2 Interact II
with some creativity you mount a new motor in the upright position..i've seen it done on a few boss machines, this will allow you to use a new modern motor.
- Fri May 23, 2014 7:38 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: pinning variable clutch on bridgeport R2E4
- Replies: 4
- Views: 3082
Re: pinning variable clutch on bridgeport R2E4
basically you just want to stop the crank handle pin which is rotated by the air motor from moving. so any way you come up with do achieve that goal will be fine.
- Thu Mar 27, 2014 9:35 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Good nema23 dc servo motor and encoder recomendation
- Replies: 1
- Views: 1906
Re: Good nema23 dc servo motor and encoder recomendation
i've used pittman motors in the past.
http://www.automationexpress.com/Produc ... otors.aspx
http://www.automationexpress.com/Produc ... otors.aspx