Search found 3097 matches
- Sun Apr 21, 2024 1:18 pm
- Forum: Centroid Hickory CNC Controller
- Topic: Hardinge CHNC II+ Hickory LeadShine EL7 Retrofit
- Replies: 96
- Views: 5428
Re: Hardinge CHNC II+ Hickory LeadShine EL7 Retrofit
You may find that you will always need a test cut. There is no way the probe can account for tool deflection and cutting forces.
- Fri Apr 19, 2024 7:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Touch probe
- Replies: 20
- Views: 832
Re: Touch probe
It looks like to me some calipers and radius gages would get that into CAD much faster.
- Thu Apr 18, 2024 8:49 pm
- Forum: Centroid Acorn CNC Controller
- Topic: VFD control voltage
- Replies: 10
- Views: 263
Re: VFD control voltage
Well, the fact that you get 10V without the VFD connect pretty much narrows it down to the VFD loading the analog out. You might try a signal isolator:
https://www.amazon.com/Isolator-Insulat ... B09TJTCDQ8
https://www.amazon.com/Isolator-Insulat ... B09TJTCDQ8
- Wed Apr 17, 2024 1:55 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 45
- Views: 2008
Re: Torchmate accumove 2 conversion
Acorn will use the steps per rev first before the revs per inch. So if you tell it to move a certain distance and you have these settings wrong it will default to the steps per rev that you have entered in the wizard... Almost there. Acorn operates in steps. People operate in inches or mm for those...
- Wed Apr 17, 2024 10:40 am
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 45
- Views: 2008
Re: Torchmate accumove 2 conversion
What do you have your motor steps set to on the drives? In the Wizard?
- Tue Apr 16, 2024 5:32 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 45
- Views: 2008
Re: Torchmate accumove 2 conversion
You need at least 3 motor revs per inch of travel for correct positioning, so you need add a belt drive between your motor and screw, or replace your screws with a smaller pitch.
Just setting the revs/inch to 3 will not work
Just setting the revs/inch to 3 will not work
- Tue Apr 16, 2024 3:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acornsix yaskawa sigma2 issue!
- Replies: 18
- Views: 436
Re: Acornsix yaskawa sigma2 issue!
Make sure your spindle motor wires are properly shielded. Separate the spindle wiring from control wires and if they have to cross, make sure it's at 90 degrees.
- Tue Apr 16, 2024 2:38 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acornsix yaskawa sigma2 issue!
- Replies: 18
- Views: 436
Re: Acornsix yaskawa sigma2 issue!
If the motor drives are not showing errors for list steps, then it is probably a noise issue. Try re-running your program with the spindle off.
- Mon Apr 15, 2024 7:07 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: WMPG-6 jogs in reverse direction
- Replies: 4
- Views: 134
Re: WMPG-6 jogs in reverse direction
You might have a look at parameter 1.
- Mon Apr 15, 2024 6:59 am
- Forum: Centroid Acorn CNC Controller
- Topic: A few problems I need help with
- Replies: 8
- Views: 269
Re: A few problems I need help with
All Acorn schematics are here. Use the search function to narrow it down to your Leadshine drives:
https://www.centroidcnc.com/centroid_di ... browse.php
https://www.centroidcnc.com/centroid_di ... browse.php