Search found 3131 matches
- Thu May 16, 2024 8:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Component FB6 near H6 header
- Replies: 9
- Views: 87
Re: Component FB6 near H6 header
My guess is a ferrite bead.
- Thu May 16, 2024 4:23 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 368
Re: Analog Out weirdness, please help
After all best practices have been employed (twisted pair shielded wire, proper grounds, bypass caps, etc.), you might want to look into a signal isolator: https://www.amazon.com/Isolator-Insulation-Reliability-Conditioner-Transmitters/dp/B09TJTCDQ8 This product did not work. It requires 24V input,...
- Thu May 16, 2024 2:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rough Motion on Circular Toolpaths
- Replies: 17
- Views: 181
Re: Rough Motion on Circular Toolpaths
Is the code a G2/3 arc move or a bunch of G1linear moves?
- Thu May 16, 2024 11:07 am
- Forum: Centroid Acorn CNC Controller
- Topic: Introduction video to using Notepad ++ and the NCnetic G code editing plugin.
- Replies: 9
- Views: 221
- Thu May 16, 2024 9:38 am
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 368
Re: Analog Out weirdness, please help
Span and slope adjustments are normally in the VFD.
- Wed May 15, 2024 12:26 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Z/W Axis summing with scale on Z axis
- Replies: 1
- Views: 39
Re: Z/W Axis summing with scale on Z axis
You CAN use the Z-axis scale for feedback. You just need the Mill Ultimate software. You will get duplicate encoder messages when you exit machine setup, but you can ignore those.
- Wed May 15, 2024 10:59 am
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 368
Re: Analog Out weirdness, please help
After all best practices have been employed (twisted pair shielded wire, proper grounds, bypass caps, etc.), you might want to look into a signal isolator:
https://www.amazon.com/Isolator-Insulat ... B09TJTCDQ8
https://www.amazon.com/Isolator-Insulat ... B09TJTCDQ8
- Wed May 15, 2024 7:38 am
- Forum: Centroid Hickory CNC Controller
- Topic: Kitamura Mycenter Zero - DELTA Ethercat Retrofit
- Replies: 13
- Views: 1043
Re: Kitamura Mycenter Zero - DELTA Ethercat Retrofit
Actually, they can transmit significantly more Hp for the same mass. I've added idlers in the middle of my long belt span on my lathe to control whip. Same principle as a tensioner.
- Mon May 13, 2024 9:44 am
- Forum: Centroid Hickory CNC Controller
- Topic: Kitamura Mycenter Zero - DELTA Ethercat Retrofit
- Replies: 13
- Views: 1043
Re: Kitamura Mycenter Zero - DELTA Ethercat Retrofit
When I changed from a double-v to J-section belt the noise was CONSIDERABLY less.
- Thu May 09, 2024 5:08 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help on isolation switch fit two circuits/power supplies
- Replies: 19
- Views: 500
Re: Help on isolation switch fit two circuits/power supplies
This is the cable that I use - "Servomotor Continuous-Flex Cable" It's gone up a little - 14Ga is now $7/ft, and 10Ga is up to $12.45/ft but still worth it.
https://www.mcmaster.com/products/multi ... lex-cable/
https://www.mcmaster.com/products/multi ... lex-cable/