Search found 3094 matches
- Wed Apr 17, 2024 1:55 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 45
- Views: 1553
Re: Torchmate accumove 2 conversion
Acorn will use the steps per rev first before the revs per inch. So if you tell it to move a certain distance and you have these settings wrong it will default to the steps per rev that you have entered in the wizard... Almost there. Acorn operates in steps. People operate in inches or mm for those...
- Wed Apr 17, 2024 10:40 am
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 45
- Views: 1553
Re: Torchmate accumove 2 conversion
What do you have your motor steps set to on the drives? In the Wizard?
- Tue Apr 16, 2024 5:32 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 45
- Views: 1553
Re: Torchmate accumove 2 conversion
You need at least 3 motor revs per inch of travel for correct positioning, so you need add a belt drive between your motor and screw, or replace your screws with a smaller pitch.
Just setting the revs/inch to 3 will not work
Just setting the revs/inch to 3 will not work
- Tue Apr 16, 2024 3:37 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acornsix yaskawa sigma2 issue!
- Replies: 16
- Views: 140
Re: Acornsix yaskawa sigma2 issue!
Make sure your spindle motor wires are properly shielded. Separate the spindle wiring from control wires and if they have to cross, make sure it's at 90 degrees.
- Tue Apr 16, 2024 2:38 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Acornsix yaskawa sigma2 issue!
- Replies: 16
- Views: 140
Re: Acornsix yaskawa sigma2 issue!
If the motor drives are not showing errors for list steps, then it is probably a noise issue. Try re-running your program with the spindle off.
- Mon Apr 15, 2024 7:07 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: WMPG-6 jogs in reverse direction
- Replies: 4
- Views: 93
Re: WMPG-6 jogs in reverse direction
You might have a look at parameter 1.
- Mon Apr 15, 2024 6:59 am
- Forum: Centroid Acorn CNC Controller
- Topic: A few problems I need help with
- Replies: 8
- Views: 235
Re: A few problems I need help with
All Acorn schematics are here. Use the search function to narrow it down to your Leadshine drives:
https://www.centroidcnc.com/centroid_di ... browse.php
https://www.centroidcnc.com/centroid_di ... browse.php
- Mon Apr 15, 2024 6:53 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: NPT + Threads in Intercon - Workflow
- Replies: 8
- Views: 210
Re: NPT + Threads in Intercon - Workflow
I cut 0-80 and M1 all the time. You need an extremely sharp tool and very small infeeds. As for cutting into your shoulder, where are you setting your Z0 for the threading tool. If you use the point of the tool, you'll have to reduce the ending Z by 1/2 the width of the tool. I set my Z0 to the side...
- Sat Apr 13, 2024 8:22 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: NPT + Threads in Intercon - Workflow
- Replies: 8
- Views: 210
Re: NPT Threads in Intercon - Workflow
The Centroid minor diameters are only valid for threading tools with the correct root flat or radius. If you are using a sharp V threading tool, you'll have to subtract another 0.108 * pitch from the minor diameter. You need to adjust the minor diameter in the thread details page and not the tool we...
- Thu Apr 11, 2024 4:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: AcornSix - Zri Homing with linear scales
- Replies: 15
- Views: 443
Re: AcornSix - Zri Homing with linear scales
Just one point I'm sure you are aware of. The X-axis will not have an index pulse. The index pulse will be on whatever axis the SCALE is attached to.