Search found 3120 matches
- Wed May 08, 2024 3:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 35
- Views: 1706
Re: Delta ASDA-B2 ACORN WIRING INFORMATION
"That" is a snubber - https://shopcentroidcnc.com/shop/cnc-ac ... -snubbers/
- Wed May 08, 2024 12:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrading a Gorilla CNC from Flashcut to Acorn
- Replies: 10
- Views: 100
Re: Upgrading a Gorilla CNC from Flashcut to Acorn
Most people just resort to adding a relay.
- Wed May 08, 2024 12:44 pm
- Forum: Centroid Acorn CNC Controller
- Topic: New Build LMS 3990 Hi Torque Mini Mill
- Replies: 53
- Views: 4827
Re: New Build LMS 3990 Hi Torque Mini Mill
F4 Run, F2 search
- Wed May 08, 2024 7:12 am
- Forum: Centroid Acorn CNC Controller
- Topic: Help on isolation switch fit two circuits/power supplies
- Replies: 9
- Views: 155
Re: Help on isolation switch fit two circuits/power supplies
Gary has already stated the proper technique. You want a SINGLE power entry point to your machine. This is directly attached to the main disconnect. It is then divided to a series of breakers/fuses sized for the different loads. The wiring is sized to carry the amperage of the last upstream fuse. Fu...
- Tue May 07, 2024 7:43 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Clearpath MCVC Spindle Motor Control - Solved (Mike R is an absolute legend)
- Replies: 26
- Views: 4739
Re: Clearpath MCVC Spindle Motor Control - Solved (Mike R is an absolute legend)
Or, start the machine with the e-stop engaged. Good practice for any machine.
- Tue May 07, 2024 5:01 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Threading with Acorn lathe Pro
- Replies: 21
- Views: 4106
Re: Threading with Acorn lathe Pro
One thing not mentioned while using modified flank infeed is if you cut on the right flank as shown, your chips will curl towards the left. If you cut on the left flank, your chips will curl to the right which is perfect if you are threading up tight to a shoulder. Having the chips curl away from th...
- Tue May 07, 2024 1:29 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Touch probe
- Replies: 29
- Views: 1429
Re: Touch probe
If you are using the part setup routines, zero is set automatically (display will show 1/2 the probe value for X and Y and 0 only on Z). If you are using probe cycles (which it appears), then the part position in the current WCS is reported.
- Tue May 07, 2024 1:05 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Setting Up Allin1DC on an older 2axis Prototrak Mill
- Replies: 10
- Views: 146
Re: Duplicate encoder Reference in Machine Parameters?
If you hardwire your machine, then it does not have to be on a GFCI circuit.
- Mon May 06, 2024 7:09 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Threading with Acorn lathe Pro
- Replies: 21
- Views: 4106
Re: Threading with Acorn lathe Pro
It's an old thread, but the information is still correct. On the thread details screen (F7) the "thread angle" setting controls how much of the cut is on the flank of the tool. Entering 60° will cut with the tip (evenly on both flanks). I usually use 55°, or 65° depending on which way I wa...
- Sat May 04, 2024 6:52 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Pro vs Ultimate, MPG questions...
- Replies: 11
- Views: 210