https://notepad-plus-plus.org/
https://ncnetic.com/notepad-gcode-plugin
Search found 3128 matches
- Thu May 16, 2024 11:07 am
- Forum: Centroid Acorn CNC Controller
- Topic: Introduction video to using Notepad ++ and the NCnetic G code editing plugin.
- Replies: 8
- Views: 151
- Thu May 16, 2024 9:38 am
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help
- Replies: 15
- Views: 189
Re: Analog Out weirdness, please help
Span and slope adjustments are normally in the VFD.
- Wed May 15, 2024 12:26 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Z/W Axis summing with scale on Z axis
- Replies: 1
- Views: 28
Re: Z/W Axis summing with scale on Z axis
You CAN use the Z-axis scale for feedback. You just need the Mill Ultimate software. You will get duplicate encoder messages when you exit machine setup, but you can ignore those.
- Wed May 15, 2024 10:59 am
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help
- Replies: 15
- Views: 189
Re: Analog Out weirdness, please help
After all best practices have been employed (twisted pair shielded wire, proper grounds, bypass caps, etc.), you might want to look into a signal isolator:
https://www.amazon.com/Isolator-Insulat ... B09TJTCDQ8
https://www.amazon.com/Isolator-Insulat ... B09TJTCDQ8
- Wed May 15, 2024 7:38 am
- Forum: Centroid Hickory CNC Controller
- Topic: Kitamura Mycenter Zero - DELTA Ethercat Retrofit
- Replies: 12
- Views: 987
Re: Kitamura Mycenter Zero - DELTA Ethercat Retrofit
Actually, they can transmit significantly more Hp for the same mass. I've added idlers in the middle of my long belt span on my lathe to control whip. Same principle as a tensioner.
- Mon May 13, 2024 9:44 am
- Forum: Centroid Hickory CNC Controller
- Topic: Kitamura Mycenter Zero - DELTA Ethercat Retrofit
- Replies: 12
- Views: 987
Re: Kitamura Mycenter Zero - DELTA Ethercat Retrofit
When I changed from a double-v to J-section belt the noise was CONSIDERABLY less.
- Thu May 09, 2024 5:08 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Help on isolation switch fit two circuits/power supplies
- Replies: 19
- Views: 483
Re: Help on isolation switch fit two circuits/power supplies
This is the cable that I use - "Servomotor Continuous-Flex Cable" It's gone up a little - 14Ga is now $7/ft, and 10Ga is up to $12.45/ft but still worth it.
https://www.mcmaster.com/products/multi ... lex-cable/
https://www.mcmaster.com/products/multi ... lex-cable/
- Thu May 09, 2024 11:28 am
- Forum: Centroid Acorn CNC Controller
- Topic: Help on isolation switch fit two circuits/power supplies
- Replies: 19
- Views: 483
Re: Help on isolation switch fit two circuits/power supplies
I have 4 machines with VFDs in the control box. Two are Yaskawa, one is a Baldor, and one is ABB. As Gary says, the amount of noise radiated from the VFD is very low on name brands. And, I'm using $6/ft shielded inverter cable, properly grounded, for the motor connections. You don't have to house th...
- Wed May 08, 2024 3:06 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Delta ASDA-B2 ACORN WIRING INFORMATION
- Replies: 48
- Views: 2583
- Wed May 08, 2024 12:46 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrading a Gorilla CNC from Flashcut to Acorn
- Replies: 12
- Views: 331
Re: Upgrading a Gorilla CNC from Flashcut to Acorn
Most people just resort to adding a relay.