Search found 3135 matches
- Tue May 21, 2024 7:10 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Undefined PLC Messages
- Replies: 5
- Views: 70
Re: Undefined PLC Messages
The easiest way is to do a re-install carefully following these instructions: https://www.centroidcnc.com/centroid_diy/downloads/centroid_cnc12_download/cnc12_v5.0_install_instructions.pdf Or, since the exe installer is just a Zip file, you can open it with something like 7Zip, and extract the plc m...
- Sun May 19, 2024 2:30 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Undefined PLC Messages
- Replies: 5
- Views: 70
Re: Undefined PLC Messages
If you had included a report, we could check that the plc message file matched the plc file that was loaded. These undefined messages usually occur because the PLC file and the message file are from different revisions or configurations.
- Fri May 17, 2024 10:59 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Z Axis lag - Loosing position
- Replies: 11
- Views: 284
Re: Z Axis lag - Loosing position
If the Z-axis moves with power off, then you will lose position. Do you have a brake on the Z-axis motor?
- Fri May 17, 2024 10:57 pm
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: CNC12 Router Restructure Beta Software thread.
- Replies: 3
- Views: 204
Re: CNC12 Router Restructure Beta Software thread.
You can install the offline version of CNC12 to preview g-code, or use Notepad++ with the NCnetic plugin.
- Thu May 16, 2024 8:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Component FB6 near H6 header
- Replies: 9
- Views: 144
Re: Component FB6 near H6 header
My guess is a ferrite bead.
- Thu May 16, 2024 4:23 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 523
Re: Analog Out weirdness, please help
After all best practices have been employed (twisted pair shielded wire, proper grounds, bypass caps, etc.), you might want to look into a signal isolator: https://www.amazon.com/Isolator-Insulation-Reliability-Conditioner-Transmitters/dp/B09TJTCDQ8 This product did not work. It requires 24V input,...
- Thu May 16, 2024 2:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rough Motion on Circular Toolpaths
- Replies: 26
- Views: 409
Re: Rough Motion on Circular Toolpaths
Is the code a G2/3 arc move or a bunch of G1linear moves?
- Thu May 16, 2024 11:07 am
- Forum: Centroid Acorn CNC Controller
- Topic: Introduction video to using Notepad ++ and the NCnetic G code editing plugin.
- Replies: 9
- Views: 299
- Thu May 16, 2024 9:38 am
- Forum: Centroid Acorn CNC Controller
- Topic: Analog Out weirdness, please help <DYN4 as spindle motor>
- Replies: 35
- Views: 523
Re: Analog Out weirdness, please help
Span and slope adjustments are normally in the VFD.
- Wed May 15, 2024 12:26 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Z/W Axis summing with scale on Z axis
- Replies: 1
- Views: 53
Re: Z/W Axis summing with scale on Z axis
You CAN use the Z-axis scale for feedback. You just need the Mill Ultimate software. You will get duplicate encoder messages when you exit machine setup, but you can ignore those.