Search found 54 matches
- Fri May 31, 2024 12:31 pm
- Forum: Buy, Sell, Trade
- Topic: Cincinnati Milicron Hawk 200 Asking $4000 OBO
- Replies: 0
- Views: 5472
Cincinnati Milicron Hawk 200 Asking $4000 OBO
For sale. Running but electronics are temperamental... great retrofit project or fixer upper! Going to part out soon to get it out of here as we need room for a new machine. Tooling on turret not included. S26 Collet Chuck installed (Collets included), and Hydraulic 8” 3 jaw Chuck. We need to get ri...
This post has been liked 0 time(s).
- Thu Dec 14, 2023 11:31 am
- Forum: Buy, Sell, Trade
- Topic: AnTek 48V 500W Power Supply
- Replies: 0
- Views: 10083
AnTek 48V 500W Power Supply
Used this for a couple of years to power our 4th axis motor. We just replaced the motor with different voltage and no longer need this power supply. It is in perfect working condition. Selling price is $75 plus shipping. PM with your full address for a shipping quote. https://www.antekinc.com/ps-5n4...
This post has been liked 0 time(s).
- Mon Dec 11, 2023 4:33 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 4th axis motor trying to turn before brake is actually released
- Replies: 17
- Views: 7566
Re: 4th axis motor trying to turn before brake is actually released
CNCSNW,
You were correct, after doing it on the second line the pause is there. THANK YOU!! I just ran a test program center drilling on 3 sides of a part and it worked great!
You were correct, after doing it on the second line the pause is there. THANK YOU!! I just ran a test program center drilling on 3 sides of a part and it worked great!
This post has been liked 0 time(s).
- Mon Dec 11, 2023 4:12 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 4th axis motor trying to turn before brake is actually released
- Replies: 17
- Views: 7566
Re: 4th axis motor trying to turn before brake is actually released
It sounds like the PLC program is wrong then. The "board" has output 6 labeled as the clamp so that's what its hooked up to. How do I go about changing the PLC program? and, why does the brake lock and release if the macro's both say output 4?? Now I'm really confused.
This post has been liked 0 time(s).
- Mon Dec 11, 2023 3:40 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 4th axis motor trying to turn before brake is actually released
- Replies: 17
- Views: 7566
Re: 4th axis motor trying to turn before brake is actually released
My machine is setup so M10 turns on the brake (closes output 6) and M11 Releases the Brake (Opens output 6).
This post has been liked 0 time(s).
- Mon Dec 11, 2023 11:53 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 4th axis motor trying to turn before brake is actually released
- Replies: 17
- Views: 7566
Re: 4th axis motor trying to turn before brake is actually released
I tried the macros this morning and still no pause. Attached is a new report. To test this i have been going to MIDI and typing in: M10 then cycle start to apply the brake. Then Typing in M11 A180 then cycle start and I get an "instant" stall with no pause before the stall. I even entered ...
This post has been liked 0 time(s).
- Fri Dec 08, 2023 12:23 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 4th axis motor trying to turn before brake is actually released
- Replies: 17
- Views: 7566
Re: 4th axis motor trying to turn before brake is actually released
I tried adding G4 P1.5 to the next line under the M95 /4 and get no pause.
This post has been liked 0 time(s).
- Fri Dec 08, 2023 11:01 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 4th axis motor trying to turn before brake is actually released
- Replies: 17
- Views: 7566
Re: 4th axis motor trying to turn before brake is actually released
Below is a picture of the CNCM.M11 File. Where do I type in the G4 parameter. An example would be nice as I'm not familiar with macro's
This post has been liked 0 time(s).
- Thu Dec 07, 2023 6:35 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 4th axis motor trying to turn before brake is actually released
- Replies: 17
- Views: 7566
Re: 4th axis motor trying to turn before brake is actually released
It’s the pneumatic brake on the 4th axis, the motor does not have a brake. Is there any instructions on how to get to this file to edit it?
This post has been liked 0 time(s).
- Thu Dec 07, 2023 5:06 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 4th axis motor trying to turn before brake is actually released
- Replies: 17
- Views: 7566
Re: 4th axis motor trying to turn before brake is actually released
S-K Machine, While that would work I'd prefer to have a parameter set in the machine. When M11 is called out there should be a way to have a slight pause before rotation. I only need a fraction of a second. I literally can set the feed rate at about 60 percent and it runs fine. Or I can disconnect t...
This post has been liked 0 time(s).