I checked the limit switch yesterday, over riding with the dip.
What would be the address to ship too, and approximate cost for repair?
Search found 13 matches
- Wed Nov 30, 2011 11:12 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 411 "Full power without motion"
- Replies: 3
- Views: 2610
- Tue Nov 29, 2011 11:22 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: 411 "Full power without motion"
- Replies: 3
- Views: 2610
411 "Full power without motion"
Good evening, A customer of mine had the Micro ATX power supply on the "All in one Unit" go out, witch was giving them a fiber optics com fault. I help them install a new power supply, and the machine started up fine but has one problem with Y axis. You can jog Y negative fine, but positiv...
- Mon Jul 18, 2011 9:28 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: ***RESOLVED*** Machine Setup Not Complete
- Replies: 4
- Views: 2972
Re: Machine Setup Not Complete
Ok, I did the test and all axis failed due to: home position close to encoder index.
So I guess if tomorrow night I move the home/Limit switches I will be ok.
So I guess if tomorrow night I move the home/Limit switches I will be ok.
- Sun Jul 17, 2011 3:15 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: ***RESOLVED*** Machine Setup Not Complete
- Replies: 4
- Views: 2972
***RESOLVED*** Machine Setup Not Complete
The machine I am working on seems to be ready to go. It homes ok, all axis and spindle work. I have writen and ran a small test program that worked perfectly. The only thing I see on the screen that I need to fix is a message at start up thats states: MACHINE SETUP NOT COMPLETE MACHINE IS NOT READY ...
- Sat Jul 16, 2011 4:35 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X,Y,Z IDELING TOO HIGH
- Replies: 4
- Views: 3292
Re: X,Y,Z IDELING TOO HIGH
Used Auto tune, and now only Z will idel too high.
Also when I start the machine, I dont see any way to home the machine. Is this because I am in demo mode or am I missing something?
Also when I start the machine, I dont see any way to home the machine. Is this because I am in demo mode or am I missing something?
- Sat Jul 16, 2011 3:42 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: **RESOLVED** Bridgeport Spindle
- Replies: 1
- Views: 1886
**RESOLVED** Bridgeport Spindle
I have a Bridgeport that I am retrofiting, Im told we should be able to controll the RPM and Breaking system.
The machine has one sensor for High/Low gear position.
One sensor for RPM's .
It has 3 valves that control the RPM's & Breaking.
Is there any information on how to wire this?
The machine has one sensor for High/Low gear position.
One sensor for RPM's .
It has 3 valves that control the RPM's & Breaking.
Is there any information on how to wire this?
- Sat Jul 16, 2011 2:33 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X,Y,Z IDELING TOO HIGH
- Replies: 4
- Views: 3292
Re: X,Y,Z IDELING TOO HIGH
The machine also does a lot of flickerig in the tens. The screen may show between 1.2498 to 1.2500 when ideling.
- Sat Jul 16, 2011 2:10 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: X,Y,Z IDELING TOO HIGH
- Replies: 4
- Views: 3292
X,Y,Z IDELING TOO HIGH
Im getting a X,Y,Z ideling too high: releasing power alarm after less then 5 mins of ideling. x,y,z are all in the middle of travel and free to move. I also some how have all axis moving & counting in the correct direction, but X axis on the keyboard is backwards. Any help with this would be gre...
- Mon Jul 11, 2011 2:43 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Low Encoder Output
- Replies: 11
- Views: 8252
Re: Low Encoder Output
It was 1000 CPR, I'll let you know the MFG this Saturday. Hope to have this machine finished this coming weekend. Only lacking getting the spindle running and finish configure the axis and backlash. Currenly my Y & Z home in the right direction but X does not, I will have to review it this comin...
- Sun Jul 10, 2011 4:42 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Low Encoder Output
- Replies: 11
- Views: 8252
Re: Low Encoder Output
The encoder are ERO 120 250 IdNr. 220 155 16
System ID is XBJDDIIJHEC (0603110344)
I changed A+ with B+ and A- with B- and now they count correct.
.
System ID is XBJDDIIJHEC (0603110344)
I changed A+ with B+ and A- with B- and now they count correct.
.