Search found 25 matches
- Fri Jan 28, 2011 11:20 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Cant Thread
- Replies: 1
- Views: 1950
Cant Thread
I put a new ajax controller on my Lathe. It uses centroid for the operating program. been using it for a few months without spindle encoder because the old one wasn't the right one. Finally got a new one and installed it. after changing all the right parameters. it would show the spindle RPM's but i...
- Mon Nov 01, 2010 3:35 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: programing axis parameters
- Replies: 23
- Views: 12414
Re: programing axis parameters
I'm running them in current mode.
- Mon Nov 01, 2010 2:52 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: programing axis parameters
- Replies: 23
- Views: 12414
Re: programing axis parameters
Hey Scott I got everything working in the line of communication, but the motors over compensate. they fly back and forth till I get a axis positional error. when i turn the motor by hand it wants to correct it and does to an extent. but when I turn a little too much it starts flying back and forth a...
- Fri Oct 29, 2010 12:31 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: programing axis parameters
- Replies: 23
- Views: 12414
Re: programing axis parameters
And now its telling me that my demo version has expired. even tho 10 minutes ago i had 9 days left.
- Fri Oct 29, 2010 12:20 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: programing axis parameters
- Replies: 23
- Views: 12414
Re: programing axis parameters
Thank goodness for tech support. A-M-C guy reminded me that inverting the inhibit inverts all the inhibits but the directional inhibits dont cause a fault. that was my problem with the drives. now to get the gpio4d to enable the drives???
- Fri Oct 29, 2010 11:22 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: programing axis parameters
- Replies: 23
- Views: 12414
Re: programing axis parameters
Ok just tested the drives again. they wont move. must have done something to them that wrecked them or something.
- Fri Oct 29, 2010 11:06 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: programing axis parameters
- Replies: 23
- Views: 12414
Re: programing axis parameters
oh I thought it was a separate setting for just the lathe screen. anyway now that I switched the dipswitches to currant mode, the board wont enable the axis. do I have to change the PID settings back to what they were, or set it up for torque mode?
- Thu Oct 28, 2010 6:25 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: programing axis parameters
- Replies: 23
- Views: 12414
Re: programing axis parameters
Scott could you tell me how to adjust the resolution on the screen? It turned big on me again.
- Thu Oct 28, 2010 11:29 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: programing axis parameters
- Replies: 23
- Views: 12414
Re: programing axis parameters
Scott where is that software that you wanted me to download, or do you want to do it when your hooked up? everything's ready now
- Wed Oct 27, 2010 2:11 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: programing axis parameters
- Replies: 23
- Views: 12414
Re: programing axis parameters
I can hook the computer up to the net if theres any way you can connect to it and see whats up.