Search found 26 matches
- Sat Apr 20, 2019 2:05 am
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrade Software License Stops Working
- Replies: 4
- Views: 1424
Re: Upgrade Software License Stops Working
I just got another file from one of the tech guys. It also does not load and says ERROR. Just tried it today. Highly disappointing. I have not mixed them up, I have them in dated folders, in Dropbox. I can also pull them from original emails. Nancy (I hope I got her name right, going from memory) se...
- Mon Apr 15, 2019 11:12 am
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrade Software License Stops Working
- Replies: 4
- Views: 1424
Re: Upgrade Software License Stops Working <answered>
It does not work (again). The first license sent never worked. The second sent worked after updating the software. I was busy debugging and did not install it before. Somehow, what was once working no longer works! My software reverted back to FREE. See the photo posted? It says ERROR...the serial n...
- Sun Apr 14, 2019 9:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrade Software License Stops Working
- Replies: 4
- Views: 1424
Upgrade Software License Stops Working
Poor description, probably! Had to take some time off from working on my machine. Did a little rewire to see if I could fix the Z axis fault problem, loaded a file larger than 50K to test, it does not run... Apparently my software has reverted back to the free version. I tried two previous codes sen...
- Thu Mar 28, 2019 4:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Sometimes a PLC is the right solution
- Replies: 29
- Views: 9330
Re: Sometimes a PLC is the right solution
It's been a while since I reported on how the AutomationDirect PLCs are working with the Acorn board. I started out with the CLICK C0-10DRE-D (Ethernet, RS232, Relay outputs, about $175 with PS). Next I tried a C0-11DRE-D (same as the other but with an RS485 modbus port, about $200 with PS). Then I...
- Mon Mar 18, 2019 9:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Vetting Clearpath S14972 Schematic
- Replies: 18
- Views: 5366
Re: Vetting Clearpath S14972 Schematic
I actually had this somewhat neat on my mockup board before all the problems! Now I am wiring 'overland.' So much for planning!
- Mon Mar 18, 2019 8:57 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Vetting Clearpath S14972 Schematic
- Replies: 18
- Views: 5366
Re: Vetting Clearpath S14972 Schematic
Ray, How have you configured the HLFB signal in the ClearPath Setup software? I've set the HLFB signal to "Servo On", that way anytime the servo's Enable signal is active, the HLFB signal is also active. The other settings, "ASG-Position", "In Range", "Speed Outpu...
- Mon Mar 18, 2019 3:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Vetting Clearpath S14972 Schematic
- Replies: 18
- Views: 5366
Re: Vetting Clearpath S14972 Schematic
Ray, I use an actual PLC, the CLICK C0-10DRE-D from Automation Direct. Automation Direct has models starting at $69. I use an ethernet model for ease of programming. I also have the C0-11DRE-D and the Productivity 1000 P1-540. Each of those PLCs has a power supply from Automation Direct and various...
- Mon Mar 18, 2019 3:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Vetting Clearpath S14972 Schematic
- Replies: 18
- Views: 5366
Re: Vetting Clearpath S14972 Schematic
" The Clearpath servo needs to be enabled prior to the HL circuit closing. That being the case, my Acorn requires a command for movement prior to enabling the servo. Once enabled the relays to close, not fast enough however to stop the fault that follows movement and an open DriveOk circuit.&q...
- Mon Mar 18, 2019 12:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Vetting Clearpath S14972 Schematic
- Replies: 18
- Views: 5366
Re: Vetting Clearpath S14972 Schematic
The Centroid supplied relay board is a 5vdc optocoupled board. The current required to operate the optocouplers is well within the Clearpath HLFB specifications. I have this layout wired on the test bench right now and it's working fine. ... you have this working with actual Clearpath SDSK servos, ...
- Mon Mar 18, 2019 11:56 am
- Forum: Centroid Acorn CNC Controller
- Topic: Vetting Clearpath S14972 Schematic
- Replies: 18
- Views: 5366
Re: Vetting Clearpath S14972 Schematic
I am not using the relay board shown in the example, so my results will not match what the diagram is showing. On my ClearPath motors, I have the HLFB (+) lines each tied to +24VDC. The HLFB (-) lines are tied to individual PLC input lines, as per the ClearPath documentation. The PLC sorts out the ...