Search found 366 matches
- Tue Mar 26, 2024 11:05 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: CNC12 v5.1 Release Candidate #2 is now available.
- Replies: 12
- Views: 434
Re: CNC12 v5.1 Release Candidate #2 is now available.
Is it possible that this issue has crept back in? I am not able to get TT or probing to work as it used to, and it seems to be acting similar the the linked post. Parameter 404 is set, but it makes no difference this time. Auto Z to plate does not stop upon touch. The input for TT does trip in the ...
- Thu Mar 21, 2024 3:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Setup
- Replies: 36
- Views: 867
Re: Rigid Tapping Setup
Richard, pending your "crossed fingers" it might be worthwhile reviewing the thread on my router where Marc Leonard helped me enormously from start to a very satisfactory finish
https://centroidcncforum.com/viewtopic.php?f=60&t=5561
https://centroidcncforum.com/viewtopic.php?f=60&t=5561
- Thu Mar 21, 2024 11:29 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Setup
- Replies: 36
- Views: 867
Re: Rigid Tapping Setup
Yes, that's how I have my system but ensure the cap is ceramic
- Wed Mar 20, 2024 5:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Setup
- Replies: 36
- Views: 867
Re: Rigid Tapping Setup
No, the 0.1 UF ceramic cap needs to be fitted between Acorn's analog Vout and Com terminals. It assisted me in bringing RPM under proper control and many other folk in stabilising their analog output. You normally don't need anything else other than proper shielded wiring best practice throughout
- Wed Feb 28, 2024 5:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 V5.08 VCP Rapid/Feed Panel Issue/Bug <self resolved>
- Replies: 14
- Views: 429
- Sun Feb 25, 2024 2:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Intercon enhancement request
- Replies: 8
- Views: 337
Re: Intercon enhancement request
You didn't mention air blast in your original post and I did mention "and/or Vac for evac". No matter, if you wish to ignore best practice that's your choice of course. For finish cuts in Intercon, suggest your refer to the Mill manual chapter 10 and the section on Sub Programs, specifical...
- Sat Feb 24, 2024 11:08 am
- Forum: Centroid Acorn CNC Controller
- Topic: Intercon enhancement request
- Replies: 8
- Views: 337
Re: Intercon enhancement request
Checkout fog buster by Noga which can be used used in air blast only and/or use vac for evac. No offence but allowing any machining of chips will damage or break you bit perhaps sooner than later with disastrous consequences
- Thu Feb 22, 2024 1:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: MDI Spindle Voltage Incorrect
- Replies: 5
- Views: 218
Re: MDI Spindle Voltage Incorrect
Disconnect wires from both Vout and COM analog terminals on Acorn and measure voltage on those terminals when manually commanding 1750 rpm. Does this produce 5vdc
Did you clean up wiring as we suggested in your other thread?
And PLEASE, post a new and current Report.zip
Did you clean up wiring as we suggested in your other thread?
And PLEASE, post a new and current Report.zip
- Tue Feb 20, 2024 8:56 am
- Forum: Centroid Acorn CNC Controller
- Topic: Lathe CAM post processor
- Replies: 2
- Views: 117
Re: Lathe CAM post processor
Since both Catia and Solidworks are under the Dassault umbrella, perhaps the following post may help
https://centroidcncforum.com/viewtopic.php?f=60&t=4101
https://centroidcncforum.com/viewtopic.php?f=60&t=4101
- Tue Feb 20, 2024 8:33 am
- Forum: Centroid Acorn CNC Controller
- Topic: Safe Spindle Temperature?
- Replies: 23
- Views: 785
Re: Safe Spindle Temperature?
How about researching if Ceramic Bearings could be an option assuming they are available in your size. My air cooled Router spindle uses this up to 24K rpm but does need 10 minute warm up before use. However, I don't know the suitability for a Mill