Search found 368 matches
- Fri Apr 12, 2024 12:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: A few problems I need help with
- Replies: 8
- Views: 247
Re: A few problems I need help with
I think Terry is confusing what appears in the Program List when he clicks Windows Start. They are 2 separate Programs but CNC12 when started will automatically start the VCP. If this is not the case, please post a current REPORT.ZIP that Shawn has already requested above. This contains detailed inf...
- Thu Apr 11, 2024 4:29 pm
- Forum: Machining Strategies. Work Holding, Tool Path, Cutters, Feeds/Speeds etc.
- Topic: Newbie Intercon question
- Replies: 4
- Views: 220
Re: Newbie Intercon question
If I understand your request and ignoring the DXF part, this needs just one main Intercon command with a choice of 2 - Either Bore Array or Drill Array. Assuming your 105 holes are split 7 rows in Y Axis and 15 rows on X axis, you enter Bore or Drill Array and enter increments of nn inches (or mm) f...
- Tue Mar 26, 2024 11:05 am
- Forum: Public Beta CNC Software Testing, Discussion and Feedback
- Topic: CNC12 v5.1 Release Candidate #2 is now available.
- Replies: 14
- Views: 747
Re: CNC12 v5.1 Release Candidate #2 is now available.
Is it possible that this issue has crept back in? I am not able to get TT or probing to work as it used to, and it seems to be acting similar the the linked post. Parameter 404 is set, but it makes no difference this time. Auto Z to plate does not stop upon touch. The input for TT does trip in the ...
- Thu Mar 21, 2024 3:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Setup
- Replies: 36
- Views: 1206
Re: Rigid Tapping Setup
Richard, pending your "crossed fingers" it might be worthwhile reviewing the thread on my router where Marc Leonard helped me enormously from start to a very satisfactory finish
https://centroidcncforum.com/viewtopic.php?f=60&t=5561
https://centroidcncforum.com/viewtopic.php?f=60&t=5561
- Thu Mar 21, 2024 11:29 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Setup
- Replies: 36
- Views: 1206
Re: Rigid Tapping Setup
Yes, that's how I have my system but ensure the cap is ceramic
- Wed Mar 20, 2024 5:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Rigid Tapping Setup
- Replies: 36
- Views: 1206
Re: Rigid Tapping Setup
No, the 0.1 UF ceramic cap needs to be fitted between Acorn's analog Vout and Com terminals. It assisted me in bringing RPM under proper control and many other folk in stabilising their analog output. You normally don't need anything else other than proper shielded wiring best practice throughout
- Wed Feb 28, 2024 5:21 pm
- Forum: Centroid Acorn CNC Controller
- Topic: CNC12 V5.08 VCP Rapid/Feed Panel Issue/Bug <self resolved>
- Replies: 14
- Views: 476
- Sun Feb 25, 2024 2:55 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Intercon enhancement request
- Replies: 8
- Views: 368
Re: Intercon enhancement request
You didn't mention air blast in your original post and I did mention "and/or Vac for evac". No matter, if you wish to ignore best practice that's your choice of course. For finish cuts in Intercon, suggest your refer to the Mill manual chapter 10 and the section on Sub Programs, specifical...
- Sat Feb 24, 2024 11:08 am
- Forum: Centroid Acorn CNC Controller
- Topic: Intercon enhancement request
- Replies: 8
- Views: 368
Re: Intercon enhancement request
Checkout fog buster by Noga which can be used used in air blast only and/or use vac for evac. No offence but allowing any machining of chips will damage or break you bit perhaps sooner than later with disastrous consequences
- Thu Feb 22, 2024 1:45 pm
- Forum: Centroid Acorn CNC Controller
- Topic: MDI Spindle Voltage Incorrect
- Replies: 5
- Views: 249
Re: MDI Spindle Voltage Incorrect
Disconnect wires from both Vout and COM analog terminals on Acorn and measure voltage on those terminals when manually commanding 1750 rpm. Does this produce 5vdc
Did you clean up wiring as we suggested in your other thread?
And PLEASE, post a new and current Report.zip
Did you clean up wiring as we suggested in your other thread?
And PLEASE, post a new and current Report.zip