Search found 144 matches
- Thu Jun 01, 2023 6:19 pm
- Forum: Buy, Sell, Trade
- Topic: WTB Lathe
- Replies: 2
- Views: 6142
Re: WTB Lathe
Thank you, That is a possibility. I appreciate the lead!
- Wed May 31, 2023 11:24 am
- Forum: Buy, Sell, Trade
- Topic: WTB Lathe
- Replies: 2
- Views: 6142
WTB Lathe
All, I am looking for a older lathe that I can upgrade to Centroid control. Ideally I would like on Older Emcoturn machine with turret, A Omniturn GT75 or similar size machine. I do not want a table top machine or a large machine that would take a lot of space in my shop. I really like Centroid's co...
- Sun May 28, 2023 3:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Lathe Turret Parameters
- Replies: 2
- Views: 321
Lathe Turret Parameters
All, I am looking for parameters that control the tool changer in lathe configuration. I had the turret motor for positioning the tool turret in my lathe go out (anyone know what motor is used in an old EMCOTURN 220 for the tool turret). The closest one I could find will have to come from Europe so ...
- Wed Oct 19, 2022 4:23 pm
- Forum: Buy, Sell, Trade
- Topic: Need to hire someone.
- Replies: 1
- Views: 1431
Re: Need to hire someone.
What part of North Carolina?
- Mon Oct 03, 2022 6:04 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Ether1616 expansion board Fault
- Replies: 11
- Views: 1482
Re: Ether1616 expansion board Fault
I went back and re read the topics that where pointed out to make sure I didn't miss anything. The machine has been working fine until a week ago when I got a message that ether1616 was offline. Also auto connect issue in regards to communication does not explain what is pulling the power supply dow...
- Mon Oct 03, 2022 4:59 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Ether1616 expansion board Fault
- Replies: 11
- Views: 1482
Re: Ether1616 expansion board Fault
I finally talked with tech support today. The tech was at a loss like me and was unable to help. I am trying to understand why the board failed before I go putting in a new board.
- Fri Sep 30, 2022 10:51 am
- Forum: Centroid Acorn CNC Controller
- Topic: Ether1616 expansion board Fault
- Replies: 11
- Views: 1482
Re: Ether1616 expansion board Fault
I tried contacting tech support and I can not get anyone to answer the phone. I would like to get a new board with out having to get all the extra stuff I dont need.
- Thu Sep 29, 2022 5:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Ether1616 expansion board Fault
- Replies: 11
- Views: 1482
Re: Ether1616 expansion board Fault
When it was all hooked up the power supply light was not on at all, that is why my initial thought was bad power supply. I disconnect all the input and output and tried powering it up again and no power supply light is lit. I disconnected the expansion board and power supply light then would light. ...
- Thu Sep 29, 2022 3:30 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Ether1616 expansion board Fault
- Replies: 11
- Views: 1482
Re: Ether1616 expansion board Fault
Thank you for the information. I currently have: 4K ohm from pin 1 to gnd and 407 ohm from pin 3 to gnd for IC17 5K ohm from pin 1 to gnd and 414 ohm from pin 3 to gnd for U1 5K ohm from pin 1 to gnd and 413 ohm from pin 3 to gnd for u2. I am not seeing a direct short but there is something somewhere.
- Thu Sep 29, 2022 12:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Ether1616 expansion board Fault
- Replies: 11
- Views: 1482
Ether1616 expansion board Fault
All, A few years ago I retrofitted my lathe with Acorn with a Ether1616 expansion board and things have been working great. On Monday during normal a routine turning operation the machine stopped and fault called out. unable to restart software for any movement. After a little investigating found th...