Thanks Marty.
Appreciate everyone’s advice.
Search found 25 matches
- Fri Dec 10, 2021 9:20 am
- Forum: Centroid Acorn CNC Controller
- Topic: Homing question
- Replies: 6
- Views: 1399
- Wed Dec 08, 2021 11:11 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Homing question
- Replies: 6
- Views: 1399
Re: Homing question
Ok, that makes sense. After I rebooted, the G28 brought it back to machine zero. Losing the steps is kinda what I figured happened. Just wanted to make sure. Since the wizard is set to limit switches, I couldn’t figure why it just wouldn’t continue to run till those tripped.
That’s for the input.
Doug
That’s for the input.
Doug
- Wed Dec 08, 2021 9:05 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Homing question
- Replies: 6
- Views: 1399
Homing question
Hi Folks, I inadvertently over torqued my Clearpath motors running a job. After I cleared the motor fault with the MSP I gave the machine a G28 MDI and it didnt even come close to coming to machine zero. I then powered the whole system down and back up again. When Acorn was opened, I hit the green b...
- Tue Jan 12, 2021 10:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Please Help!! (Resolved)
- Replies: 3
- Views: 1822
Re: Please Help!!
THAT DID IT!!
So much to learn. Thank you so much.
Really appreciate it.
So much to learn. Thank you so much.
Really appreciate it.
- Tue Jan 12, 2021 10:51 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Please Help!! (Resolved)
- Replies: 3
- Views: 1822
Re: Please Help!!
ok, thats a start. Honestly I'm new to this so thank you so much. I'll read up on that.
- Tue Jan 12, 2021 9:58 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Please Help!! (Resolved)
- Replies: 3
- Views: 1822
Please Help!! (Resolved)
Anyone's help would be greatly appreciated! Here's the issue. I am trying to run this F360 program on my Acorn CNC12 Ver4.14. I keep getting an "Abnormal Job End" after I load the program and then try to Run it. I have always used F360 with success until now. I have a subscription as well....
- Sun Nov 17, 2019 5:08 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Quick question on G43
- Replies: 2
- Views: 1340
Re: Quick question on G43
Thank you very much. That answers a lot. Gives me some direction. I’ve been running some simple Fusion360 programs which I’ve had to modify a bit to get to work as far as tool changes (T1,..) Goibg to start to work the G41-42 in there now.
Thanks again
Thanks again
- Sun Nov 17, 2019 10:36 am
- Forum: Centroid Acorn CNC Controller
- Topic: Quick question on G43
- Replies: 2
- Views: 1340
Quick question on G43
I’m pretty new to this so what I’m wondering is when I call for T1(tool 1) and the G43 for the tool offset H1, can I manipulate the tool diameter in the offset library to change a diameter of an interpolated bore let’s say in the program without changing the program? This would be accounting for too...
- Thu Sep 26, 2019 12:02 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Setting ref tool heights
- Replies: 10
- Views: 4168
Re: Setting ref tool heights
Works as advertised! Proofed it out. Set the Z Ref tool in and get your number off the 123 block then put the new tool in and do the same routine. All the offsets are where they should be.
Take away: DONT RUSH THE SETUP! Proof the tool to back up its in the right place.
Thanks again everyone!
Take away: DONT RUSH THE SETUP! Proof the tool to back up its in the right place.
Thanks again everyone!
- Thu Sep 26, 2019 9:36 am
- Forum: Centroid Acorn CNC Controller
- Topic: Setting ref tool heights
- Replies: 10
- Views: 4168
Re: Setting ref tool heights
Thank you Keith. You’re right. Couldn’t see the forest through the trees here. Good idea proofing the tool against zero.
I appreciate your patience with getting me out of the weeds here as well as everyone else’s comments.
I appreciate your patience with getting me out of the weeds here as well as everyone else’s comments.