Search found 32 matches
- Sat Apr 27, 2024 2:00 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378
Re: Torchmate accumove 2 conversion
Its been a longer than I thought project, but worth it. Building the control panel was more work than I realized but taking my time to make sure I had it straight in my head paid off. I have successfully cut test parts today, and aside from the typical plasma table issues they came out great. My ohm...
- Fri Apr 26, 2024 5:55 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378
Re: Torchmate accumove 2 conversion
Well the new pc fixed the com errors, so now its on to calibrating my torch and hopefully cutting my first parts.
Thanks for all the help.
Jared
Thanks for all the help.
Jared
- Fri Apr 26, 2024 10:45 am
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378
Re: Torchmate accumove 2 conversion
Yes sir, Joey I have gone through every step and the windows firewall is completely turned off. I ran the tuner, 3 times. Then I have gone and verified all the steps manually. The only step I haven't done is the last one in the tb 270 that is inconsistent according to tb 270. There is absolutely not...
- Thu Apr 25, 2024 2:12 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378
Re: Torchmate accumove 2 conversion
Once again I need some help, After sorting out all the setup for my motors/linear motion, I have everything working, home switches/home all, laser, torch is firing, touchoff is working, ect.. I try to run a job and get communication errors. Doing a stress test over and over and trying different thin...
- Wed Apr 17, 2024 5:15 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378
Re: Torchmate accumove 2 conversion
Thanks again for all your help guys. I had a feeling it would be something simple. I corrected the dip switches and settings in the wizard and what do you know .995 revs per inch is less than a 32nd off. And at 400 ipm. With the same motors running on torchmates system 150 ipm was max without losing...
- Wed Apr 17, 2024 1:20 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378
Re: Torchmate accumove 2 conversion
20240417_131051.jpg Ok so Im just going to go crawl in a hole and hide now. Goodness I feel stupid. So what I have gathered from this humbling/learning experience is Acorn will use the steps per rev first before the revs per inch. So if you tell it to move a certain distance and you have these sett...
- Wed Apr 17, 2024 12:48 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378
Re: Torchmate accumove 2 conversion
UUHHHH do I have off and on backwards? If I do then yes it would be 12800. And that would be about right being off by a 2 thirds
I guess I assumed up was on and down was off?
Jared
I guess I assumed up was on and down was off?
Jared
- Wed Apr 17, 2024 12:20 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378
Re: Torchmate accumove 2 conversion
Oh there it is in the manual.
It says switch 9 is (PUL/DIR) or (CW/CCW) it just doesnt say which way is which
I am going to change the resolution to 6400 and see if that makes a difference.
Ill be back.
Thanks Jared
It says switch 9 is (PUL/DIR) or (CW/CCW) it just doesnt say which way is which
I am going to change the resolution to 6400 and see if that makes a difference.
Ill be back.
Thanks Jared
- Wed Apr 17, 2024 12:12 pm
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378
Re: Torchmate accumove 2 conversion
Ok here is a better picture and a picture of the manual for my drive 20240417_115814.jpg 20240314_171612 zoomed.jpg I think this is right 5=on 6=off 7=on 8=off In checking this I did notice I left the 9 and 10 the way they came. The default though was a 24v input and I switched the dip switch on the...
- Wed Apr 17, 2024 10:52 am
- Forum: Acorn CNC Plasma
- Topic: Torchmate accumove 2 conversion
- Replies: 52
- Views: 6378