Search found 8 matches
- Sat Feb 03, 2024 12:20 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: post processor for solidcam
- Replies: 1
- Views: 305
post processor for solidcam
Does anyone have a post processor for solidcam/ solidworks that would work with my 3 axis router. I can make minor adjustments just looking for something to start with.
- Wed Jan 31, 2024 9:29 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: CNC Router Following Error
- Replies: 7
- Views: 557
Re: CNC Router Following Error
The drives in question are not on Opticdirect board. I will reset to incremental encoder not sure how that got changed. I believe following error was there before encoder slipped. There was some change with parameters 341 and 344 but the error is so large it didn't clear it up significantly. I notic...
- Mon Jan 29, 2024 7:45 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: CNC Router Following Error
- Replies: 7
- Views: 557
Re: CNC Router Following Error
I like I stated have tried adjusting Position mode delay from 0 to max of 60 with minimal change. The error shows on PID screen error and tops out at 20,000 counts, I can also see it in the cuts that its lagging a huge amount. I tried Position mode settings PID settings which didn't bring error coun...
- Sun Jan 28, 2024 10:30 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: CNC Router Following Error
- Replies: 7
- Views: 557
CNC Router Following Error
I am having trouble clearing up the Y axis lagging behind on other axis's. I am getting as much as 20,000 encoder error on the paired Y axis. I have tried adjusting Parameter 341 and 344 (axis 2 and axis 5, Pair axis) with minimal change. I have tuned each drive in Sigmawin 7 separately by disconnec...
- Tue Nov 14, 2023 11:47 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Opticdirect & Oak Board setup and tuning
- Replies: 5
- Views: 1547
Re: Opticdirect & Oak Board setup and tuning
I also have question on my Y axis tuning / pairing. while tuning Y axis in sigma 7 I disconnect servo motor cable from paired drive I am not tuning and both drives is still coupled to rack. Why am I getting a "moment of inertia" of 7% on one drive and 368% on other? Attached are excel file...
- Tue Nov 14, 2023 11:36 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Opticdirect & Oak Board setup and tuning
- Replies: 5
- Views: 1547
Re: Opticdirect & Oak Board setup and tuning
I installed jumper, Opticdirect is solid "1" now as is oak board solid "1". No faults tell I hit cycle start then get z axis fault. I still just have Z axis hooked up so 300 = 1, 308 =7, axis 1 label Z. Does Yaskawa need special parameters for Opticdirect? The optic direct manual...
- Mon Nov 13, 2023 4:57 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Opticdirect & Oak Board setup and tuning
- Replies: 5
- Views: 1547
Opticdirect & Oak Board setup and tuning
I am having trouble with Opticdirect and Oak board communication fault. Need help trouble shooting fault. This router has 4 Yaskawa drives (2 paired for y axis) and 1 DMM drive (for C axis, tangential knife) I have disconnected all but Z axis which the Opticdirect board is on. I have no jumpers inst...
- Mon Nov 13, 2023 4:24 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: The Centroid CNC PC Tuner v1.3.0 has been released.
- Replies: 3
- Views: 10787
Re: The Centroid CNC PC Tuner v1.0 has been released.
Is this windows 11 compatible?