I fund the issue. The wizard Is changing it's self back to NO MPG.
https://centroidcncforum.com/viewtopic.php?f=60&t=4508
Search found 218 matches
- Sun Jan 16, 2022 2:24 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wirerless Remote note working <install Pro License>
- Replies: 4
- Views: 1117
- Sun Jan 16, 2022 1:19 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wirerless Remote note working <install Pro License>
- Replies: 4
- Views: 1117
Wirerless Remote note working <install Pro License>
I built a gang tool lathe some years back and it is dedicated to 4 jobs. The tooling setup never leaves the table. I am sure that the updates are 4 or 5 versions old if not older. It works well for my needs so I leave it alone. I powered up my system and turned on the remote and the screen is blank ...
- Tue Jun 23, 2020 3:17 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG quit working (RESOLVED)
- Replies: 15
- Views: 5996
Re: Wireless MPG quit working (RESOLVED)
What does the code have to do with it? You made this statement, "There where changes made so that the single point threading would get out of the thread fast enough to not cut a relief." I just wanted an example of the code you were using that generated the concern along with a fresh repo...
- Mon Jun 22, 2020 9:48 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG quit working (RESOLVED)
- Replies: 15
- Views: 5996
Re: Wireless MPG quit working (RESOLVED)
What does the code have to do with it?
- Mon Jun 22, 2020 9:22 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG quit working (RESOLVED)
- Replies: 15
- Views: 5996
Re: Wireless MPG quit working (RESOLVED)
I will post the report. No code and no tooling setup. Lots of research trial and err to make what I'm making. I wrote the code line by line in Note. It is a gang tool lathe. It was working flawlessly. Hundreds of parts. Start the machine home it out and push cycle start and go. Then one day the hand...
- Sun Jun 21, 2020 2:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG quit working (RESOLVED)
- Replies: 15
- Views: 5996
Re: Wireless MPG quit working (RESOLVED)
There have been a lot of changes made in the control panel. There where changes made so that the single point threading would get out of the thread fast enough to not cut a relief. One setting was to set it up as a gang tool lathe. What do I do about this? I paid Centroid tech support there hourly r...
- Sun Jun 21, 2020 2:18 am
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG quit working (RESOLVED)
- Replies: 15
- Views: 5996
Re: Wireless MPG quit working
Marty you nailed it. It was in the Wizard. I slowed down and found it.
My question is why did it change?
The one I'm pointing to was set to NO.
My question is why did it change?
The one I'm pointing to was set to NO.
- Sat Jun 20, 2020 8:33 am
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG quit working (RESOLVED)
- Replies: 15
- Views: 5996
Re: Wireless MPG quit working
I have been run this lathe for well over a year with no changes, not even a update except for new battery's in the hand held.
I opened the wizard and the hand held is selected and I am running the pro licence. The pro licence is required to used the hand held if my memory is correct.
I opened the wizard and the hand held is selected and I am running the pro licence. The pro licence is required to used the hand held if my memory is correct.
- Fri Jun 19, 2020 10:34 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG quit working (RESOLVED)
- Replies: 15
- Views: 5996
Re: Wireless MPG quit working
Done that several times. Switched places with other USB devices like the mouse and keyboard. Those devices pick right up and start working. The battery indicator shows a full set of bars and i replaced the battery's about 4 mouths ago. It doesn't display the normal dash lines like it did before homi...
- Fri Jun 19, 2020 4:16 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Wireless MPG quit working (RESOLVED)
- Replies: 15
- Views: 5996
Wireless MPG quit working (RESOLVED)
Turned on my Lathe setup a few tools shut it down to take care of something else and restated everything and the hand held only shows the Batt indicator wireless signal indicator and a little squire blinks when I move the hand wheel. No movement from the machine. I restarted the PC and acorn several...