Search found 164 matches
- Sun Jan 28, 2024 6:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Need help writing macro
- Replies: 6
- Views: 357
Re: Need help writing macro
Thank you!
- Sun Jan 28, 2024 8:31 am
- Forum: Centroid Acorn CNC Controller
- Topic: Need help writing macro
- Replies: 6
- Views: 357
Need help writing macro
I have added a laser pointer to my CNC router. It projects a + onto the workpiece. This is offset from the tool tip and I would like to write a macro to add to my pendant to set the tool position. Shortly I will post a picture of the setup if this is not clear. I think that there might be a macro al...
- Fri Nov 10, 2023 1:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Add on laser, need opinions
- Replies: 2
- Views: 376
Add on laser, need opinions
I have been looking at a J Tech laser add on for my machine. I have a Shopbot machine that I converted to Acorn six or more years ago. It has been upgraded to the point where it is almost unrecognizable. Acorn with Clearpath motors aluminum table, Etc. I would like to hear from some of you that have...
- Wed Oct 25, 2023 10:30 am
- Forum: Centroid Acorn CNC Controller
- Topic: Air Blower installation
- Replies: 8
- Views: 524
Re: Air Blower installation
Thank you! That did the trick. This setup will only be used for some plastic work that I am planning so I put a valve in the line and I can just shut of the air when I don't need it.
- Wed Oct 25, 2023 10:27 am
- Forum: Centroid Acorn CNC Controller
- Topic: Acorn 10V analog output wonky (Resolved, and not what you thought)
- Replies: 9
- Views: 673
Re: Acorn 10V analog output wonky (Resolved, and not what you thought)
I had the exact same problem and it was cured by buying a piece of good quality shielded coax rather than the Radio Shack stuff I was using.
- Tue Oct 24, 2023 12:47 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Air Blower installation
- Replies: 8
- Views: 524
Re: Air Blower installation
Then let me rephrase the question. How can I control more than one relay with one command? If I can do this I will parallel the spindle control with the air blower control and all of the existing tool paths that I have will work without modification.
- Tue Oct 24, 2023 10:48 am
- Forum: Centroid Acorn CNC Controller
- Topic: Air Blower installation
- Replies: 8
- Views: 524
Air Blower installation
I have installed an air blower system on my machine. It operates as it should when I use the control panel to turn the output (No 5) on and off. This tells me that all is well with the. wiring, the relay, and the Acorn. How do I now get the post processor to insert the code to turn it on and off. Be...
- Mon May 01, 2023 6:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Using Z zero plate with pendant
- Replies: 5
- Views: 391
Re: Using Z zero plate with pendant
Thanks for the help
- Mon May 01, 2023 1:38 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Using Z zero plate with pendant
- Replies: 5
- Views: 391
Using Z zero plate with pendant
I see where the Z Zero macro is now a part of the VCP. How do I program one of the aux keys on my pendant to start the Z Zero routine?
- Sat Mar 25, 2023 1:56 pm
- Forum: Centroid Acorn CNC Controller
- Topic: It's me again, Clearpath losing/gaining steps <resolved, loose pulley>
- Replies: 15
- Views: 1763
Re: It's me again, Clearpath losing/gaining steps
Clearpath has a good write up on the subject of clamping Here
https://teknic.com/files/downloads/Secu ... Shafts.pdf