Search found 105 matches
- Thu Sep 28, 2023 6:40 am
- Forum: Centroid Acorn CNC Controller
- Topic: Rail system
- Replies: 4
- Views: 835
Re: Rail system
I had a machinist friend put the headstock and tailstock on aluminum plates. Bolts going through the plates fasten to aluminum 'feet' that just fit in the extrusion slots of my deck. So I just loosen the bolts and slide the tailstock up the extrusion slots. It works very well. The headstock is almos...
- Wed Sep 27, 2023 1:33 pm
- Forum: Centroid Acorn CNC Controller
- Topic: cutting air
- Replies: 18
- Views: 2560
Re: cutting air
Try setting the Z0 with the 'paper method'. There is no ambiguity with the puck. When you run the program, the bit should cut properly. If it is still cutting air, note how high above the material it is. If the height above the material is the thickness of the material you set up the Z zero to Machi...
- Fri Sep 15, 2023 2:12 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Laser/Router Work Flow
- Replies: 29
- Views: 19992
Re: Laser/Router Work Flow
Excellent! This is really helpful (as usual).
I'll give it a go.
Thanks Scott
I'll give it a go.
Thanks Scott
- Fri Sep 15, 2023 8:59 am
- Forum: Centroid Acorn CNC Controller
- Topic: Laser/Router Work Flow
- Replies: 29
- Views: 19992
Re: Laser/Router Work Flow
SWord,
What line(s) of code in the "No_Z_Hop" laser post processor stop the Z-travel movements in that PP?
It's not obvious to me. I don't know if that might get in the way of combining the rotary and laser PPs, but I'd like to eliminate that as a potential issue.
Thanks,
Scott
What line(s) of code in the "No_Z_Hop" laser post processor stop the Z-travel movements in that PP?
It's not obvious to me. I don't know if that might get in the way of combining the rotary and laser PPs, but I'd like to eliminate that as a potential issue.
Thanks,
Scott
- Wed Sep 13, 2023 6:54 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Laser/Router Work Flow
- Replies: 29
- Views: 19992
Re: Laser/Router Work Flow
It seems this Vectric upgrade (11.552) adds overscan.
I've posted to the Vectric forum to see if anyone has a PP for this. Even if it isn't Centroid, I think it might teach me how to approach a modification.
Not getting anywhere with adapting the 4th axis post processor to do laser.
I've posted to the Vectric forum to see if anyone has a PP for this. Even if it isn't Centroid, I think it might teach me how to approach a modification.
Not getting anywhere with adapting the 4th axis post processor to do laser.
- Wed Sep 13, 2023 4:00 pm
- Forum: Centroid Acorn CNC Controller
- Topic: Laser/Router Work Flow
- Replies: 29
- Views: 19992
Re: Laser/Router Work Flow
Does the laser module for VCarve apply a laser toolpath on a wrapped layout? Would guess it does, but I have never tried it. Yes it does. So it can VCarve a three dimensional model created on the rotary. That works fine. The catch is getting it to do laser instead of spindle. I may be able to do th...
- Wed Sep 13, 2023 10:04 am
- Forum: Centroid Acorn CNC Controller
- Topic: Laser/Router Work Flow
- Replies: 29
- Views: 19992
Re: Laser/Router Work Flow
If you have any suggestions, please send them along. I know the Laser pp says no Z hop, but it would be nice if it could follow the shape of the cylinder. Has anyone managed to get a PP working that can laser engrave on a rotary surface model? I'm going to be engraving on a tapered cylinder. Vectri...
- Fri Sep 08, 2023 6:44 am
- Forum: Centroid Acorn CNC Controller
- Topic: Upgrading from 4.82
- Replies: 9
- Views: 2971
Re: Upgrading from 4.82
This > Configure the Acorn/AcornSix setup Wizard as per the Acorn Installation manual. Is there a better way of doing this than going through the whole Wizard dialog and filling it in based on old screenshots from the Wizard? This is the only thing holding me back from regular updates, but the pain/...
- Wed Sep 06, 2023 1:14 pm
- Forum: Centroid Acorn CNC Controller
- Topic: We are working on Adding Rapid Override controls to the VCP
- Replies: 34
- Views: 20805
Re: We are working on Adding Rapid Override controls to the VCP
Personally, I'd rather have two separate buttons when there is the chance I can break something. I want to have a discrete intentional choice with no chance of misinterpretation. Toggles for lights and coolant are one thing, cutting is another. I've kept my Start Cycle and Stop Cycle buttons physica...
- Wed Sep 06, 2023 11:38 am
- Forum: Centroid Acorn CNC Controller
- Topic: Show me your Custom VCP's!
- Replies: 283
- Views: 258132
Re: Show me your Custom VCP's!
How do I edit the left side? VCP Custom Panel.png Use the Color Picker Utility. It's under the Utilities sub menu, not through VCP. If you want to do it directly you can edit the XML file in the Colors folder. The default is Centroid Classic. If you look at the XML file I attached you can look for ...