Search found 70 matches

by AtomicAsian
Wed Nov 02, 2022 1:10 pm
Forum: Acorn CNC Plasma
Topic: Clearpath issues On new gantry
Replies: 8
Views: 1497

Re: Clearpath issues On new gantry

originally the Y has a single servo with a 10:1 and a 2 3/8 spur Everyone recommended the 5:1. clearpath even did with the smaller spur. i did change the gantry to aluminum square tube to lighten it up. Teknic support had to tune the X axis from their end manually. it helped a lot. but i still get a...
by AtomicAsian
Wed Nov 02, 2022 1:01 pm
Forum: Acorn CNC Plasma
Topic: Clearpath issues On new gantry
Replies: 8
Views: 1497

Re: Clearpath issues On new gantry

Shit thankyou.
by AtomicAsian
Fri Oct 21, 2022 8:40 pm
Forum: Acorn CNC Plasma
Topic: Clearpath issues On new gantry
Replies: 8
Views: 1497

Re: Clearpath issues On new gantry

I’ll get some shots tomorrow.
Yes 5:1 gearbox 24t pinion
by AtomicAsian
Thu Oct 20, 2022 6:00 pm
Forum: Acorn CNC Plasma
Topic: Clearpath issues On new gantry
Replies: 8
Views: 1497

Clearpath issues On new gantry

I finally built a new gantry with dual servos. Tunning and test cutting has improved. NOW I'm wanting the perfect circle and overall cuts I'm getting a jitter after lead in. circles are not great. My table is very jerky after each cut moving to the next cut. What can I do to smooth out this table? r...
by AtomicAsian
Thu Sep 22, 2022 10:36 pm
Forum: Acorn CNC Plasma
Topic: THC not responding < machine mechanicals need addressed>
Replies: 18
Views: 3039

Re: THC not responding < machine mechanicals need addressed>

I just saw a pic of your Y axis motor looks like you have a large 2 inch pinion gear on a 5 to 1 planetary that gone loose acceleration that setup you need 10 to 1 i always recommend 10 to 1 on servo and high rpm servo if that power is needed . that table used a plate rider to cut height was consta...
by AtomicAsian
Thu Sep 22, 2022 10:34 pm
Forum: Acorn CNC Plasma
Topic: THC not responding < machine mechanicals need addressed>
Replies: 18
Views: 3039

Re: THC not responding < machine mechanicals need addressed>

I’ll change it tomorrow. yes the RAS is disabled
by AtomicAsian
Thu Sep 22, 2022 12:54 pm
Forum: Acorn CNC Plasma
Topic: THC not responding < machine mechanicals need addressed>
Replies: 18
Views: 3039

Re: THC not responding

once again Joey has saved the day.
I owe him big time.
I did configure the Z axis this morning.
3.878785455. much better.
by AtomicAsian
Wed Sep 21, 2022 3:46 pm
Forum: Acorn CNC Plasma
Topic: THC not responding < machine mechanicals need addressed>
Replies: 18
Views: 3039

Re: THC not responding

so i changed anti dive threshold little by little. and I’m at 60%
100v at 30 amps.
It’s does great on X axis cuts BUT on Y axis it gets away from the surface more and Z axis doesn’t change. goes back to X and it works. back down to Y. locks in. Very weird video and pic in album
by AtomicAsian
Wed Sep 21, 2022 9:19 am
Forum: Acorn CNC Plasma
Topic: THC not responding < machine mechanicals need addressed>
Replies: 18
Views: 3039

Re: THC not responding

Thankyou guys. I will give it a shot