Search found 70 matches
- Wed Nov 02, 2022 1:10 pm
- Forum: Acorn CNC Plasma
- Topic: Clearpath issues On new gantry
- Replies: 8
- Views: 1579
Re: Clearpath issues On new gantry
originally the Y has a single servo with a 10:1 and a 2 3/8 spur Everyone recommended the 5:1. clearpath even did with the smaller spur. i did change the gantry to aluminum square tube to lighten it up. Teknic support had to tune the X axis from their end manually. it helped a lot. but i still get a...
- Wed Nov 02, 2022 1:01 pm
- Forum: Acorn CNC Plasma
- Topic: Clearpath issues On new gantry
- Replies: 8
- Views: 1579
Re: Clearpath issues On new gantry
Shit thankyou.
- Fri Oct 21, 2022 8:40 pm
- Forum: Acorn CNC Plasma
- Topic: Clearpath issues On new gantry
- Replies: 8
- Views: 1579
Re: Clearpath issues On new gantry
I’ll get some shots tomorrow.
Yes 5:1 gearbox 24t pinion
Yes 5:1 gearbox 24t pinion
- Thu Oct 20, 2022 6:00 pm
- Forum: Acorn CNC Plasma
- Topic: Clearpath issues On new gantry
- Replies: 8
- Views: 1579
Clearpath issues On new gantry
I finally built a new gantry with dual servos. Tunning and test cutting has improved. NOW I'm wanting the perfect circle and overall cuts I'm getting a jitter after lead in. circles are not great. My table is very jerky after each cut moving to the next cut. What can I do to smooth out this table? r...
- Thu Sep 22, 2022 10:36 pm
- Forum: Acorn CNC Plasma
- Topic: THC not responding < machine mechanicals need addressed>
- Replies: 18
- Views: 3312
Re: THC not responding < machine mechanicals need addressed>
I just saw a pic of your Y axis motor looks like you have a large 2 inch pinion gear on a 5 to 1 planetary that gone loose acceleration that setup you need 10 to 1 i always recommend 10 to 1 on servo and high rpm servo if that power is needed . that table used a plate rider to cut height was consta...
- Thu Sep 22, 2022 10:34 pm
- Forum: Acorn CNC Plasma
- Topic: THC not responding < machine mechanicals need addressed>
- Replies: 18
- Views: 3312
Re: THC not responding < machine mechanicals need addressed>
I’ll change it tomorrow. yes the RAS is disabled
- Thu Sep 22, 2022 12:54 pm
- Forum: Acorn CNC Plasma
- Topic: THC not responding < machine mechanicals need addressed>
- Replies: 18
- Views: 3312
Re: THC not responding
once again Joey has saved the day.
I owe him big time.
I did configure the Z axis this morning.
3.878785455. much better.
I owe him big time.
I did configure the Z axis this morning.
3.878785455. much better.
- Wed Sep 21, 2022 3:48 pm
- Forum: Acorn CNC Plasma
- Topic: THC not responding < machine mechanicals need addressed>
- Replies: 18
- Views: 3312
Re: THC not responding
report
- Wed Sep 21, 2022 3:46 pm
- Forum: Acorn CNC Plasma
- Topic: THC not responding < machine mechanicals need addressed>
- Replies: 18
- Views: 3312
Re: THC not responding
so i changed anti dive threshold little by little. and I’m at 60%
100v at 30 amps.
It’s does great on X axis cuts BUT on Y axis it gets away from the surface more and Z axis doesn’t change. goes back to X and it works. back down to Y. locks in. Very weird video and pic in album
100v at 30 amps.
It’s does great on X axis cuts BUT on Y axis it gets away from the surface more and Z axis doesn’t change. goes back to X and it works. back down to Y. locks in. Very weird video and pic in album
- Wed Sep 21, 2022 9:19 am
- Forum: Acorn CNC Plasma
- Topic: THC not responding < machine mechanicals need addressed>
- Replies: 18
- Views: 3312
Re: THC not responding
Thankyou guys. I will give it a shot