Search found 17 matches
- Sun Mar 10, 2024 7:37 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Mastercam
- Replies: 2
- Views: 390
Mastercam
Hi , firstly I would like to say I’m not the best at fully understanding the computer side of my control so please excuse any thing I may get wrong. I have a 2002 cnc machining centre which died a few years back .. however the M400 control was working fine and I have used it purely for the Mastercam...
- Fri Jul 08, 2022 2:52 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Another screen problem
- Replies: 9
- Views: 1458
Re: Another screen problem
I will check this out cncsnw …
I’ve never been in Bios on this machine cncjeff1
I’ve never been in Bios on this machine cncjeff1
- Thu Jul 07, 2022 10:50 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Another screen problem
- Replies: 9
- Views: 1458
Re: Another screen problem
I tried connecting a monitor to the cable in picture but nothing showed on monitor…should have worked?
- Thu Jul 07, 2022 4:40 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Another screen problem
- Replies: 9
- Views: 1458
Re: Another screen problem
Hi, after following your information I can confirm that the LEDs light and it jogs and moves fine . If I now do as you suggest and investigate the descrambler, is it something I can repair or replace ?
- Wed Jul 06, 2022 4:03 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Another screen problem
- Replies: 9
- Views: 1458
Re: Another screen problem
Hi thanks for reply, yes the in jog panel lights . .. have noticed there are a series of beeps on start up .. more than it normally did .. not sure if that means anything ? Is it difficult to check the ribbon and descrambler board ?
- Wed Jul 06, 2022 9:02 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Another screen problem
- Replies: 9
- Views: 1458
Another screen problem
Hi , I have another screen problem on a different machine.
After a short power cut the machine came back on with the screen like this , any ideas what’s wrong ? Thanks
After a short power cut the machine came back on with the screen like this , any ideas what’s wrong ? Thanks
- Mon Jul 04, 2022 4:09 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Screen display
- Replies: 13
- Views: 2175
Re: Screen display
Worked absolutely perfect , thank you so much for all your help
- Fri Jul 01, 2022 8:25 am
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Screen display
- Replies: 13
- Views: 2175
Re: Screen display
Ok , so I managed to load the language MSG file and it all looked good , it got past that screen and I thought it was going to be ok… however it’s now stuck on this screen.. can you help again please … many thanks
- Thu Jun 30, 2022 3:14 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Screen display
- Replies: 13
- Views: 2175
Re: Screen display
it is strange as the control was fine before I changed the date and time and screen resolution {all be it too large for the screen}
- Thu Jun 30, 2022 2:57 pm
- Forum: Centroid Oak, Allin1DC, MPU11 and Legacy products
- Topic: Screen display
- Replies: 13
- Views: 2175
Re: Screen display
I have a floppy drive and I think I could unpack the zip file and copy the MSG file to a disc ok … but I think copying it to the C:\CNC7 directory on my control is a bit beyond me. Is there any chance you could tell me how to do that in a kind of computers for dummy’s way ?